Δεχόμαστε κρυπτονομίσματα — έτσι ώστε αυτά που κατέχετε να μπορούν να αγοράσουν πραγματικό εξοπλισμό.Πληρώστε σε κρυπτονομίσματα, ξοδέψτε τα σε πραγματικό εξοπλισμό. Δωρεάν ασφαλισμένη αποστολή παγκοσμίως άνω των 399 $. Ουδέτερες κούτες αποστολής, χωρίς σήμανση, από τη Γερμανία.Δωρεάν ασφαλισμένη αποστολή άνω των 399 $. Η ισοτιμία σας κλειδώνει για 30 λεπτά μόλις ανοίξει το ταμείο.Κλείδωμα ισοτιμίας 30 λεπτών. Κάθε προϊόν είναι σφραγισμένο, ελεγμένο ως προς τον σειριακό αριθμό του, και καλύπτεται από εγγύηση 24 μηνών.Σφραγισμένο, με εγγύηση 24 μηνών.

Παρακολουθούμενα είδη Σύνδεση
Silver 3.5 inch bare SATA hard drive with circuit board visible

DELL

DELL 400-ANPB 8TB 3.5" SATA 7200 RPM internal hard drive

SKU CH-VKYW-HFAAE

An 8 TB 3.5" SATA 7200 RPM internal hard drive with a 6.0 Gb/s interface and hot-swap support for Dell PowerEdge servers

  • PackagingBare Drive
  • InterfaceSATA 6.0Gb/s
  • Capacity8TB
  • RPM7200 RPM
  • Average Latency6Gb/s
  • Form Factor3.5"
  • 8 TB capacity stores large datasets
  • 7200 RPM spindle speed delivers responsive throughput
  • SATA 6.0 Gb/s interface supports high bandwidth
  • 5 inch form factor fits standard bays
  • Hot-swappable design enables drive changes without downtime

Dell 400-ANPB 8TB 3.5" SATA Drive

The Dell 400-ANPB is a new 8TB internal hard drive built for desktop and server storage. It uses a 3.5 inch form factor and connects through a SATA 6.0Gb/s interface. The drive spins at 7200 RPM for responsive data access. It arrives as a bare drive without retail packaging or cables.

Suited for capacity-focused storage in Dell

This drive fits administrators who need 8TB of hot-swappable storage inside compatible Dell PowerEdge systems. The 7200 RPM spindle speed supports general-purpose workloads and bulk data retention. Builders using non-Dell chassis or controllers should verify tray and firmware compatibility first. Users who require solid-state speed or smaller 2.5 inch form factors should consider other drive types.

Hot-swappable 3.5" SATA interface for PowerEdge bays

The drive uses a standard SATA 6.0Gb/s connection and is specified as hot-swappable for supported Dell PowerEdge servers. This allows drive replacement without powering down the system when the chassis and backplane support the feature. Confirm that your server model lists the 400-ANPB part number before installation. The bare-drive packaging means mounting hardware is not included.

Βασικά χαρακτηριστικά

  • 8 TB capacity stores large datasets
  • 7200 RPM spindle speed delivers responsive throughput
  • SATA 6.0 Gb/s interface supports high bandwidth
  • 5 inch form factor fits standard bays
  • Hot-swappable design enables drive changes without downtime

Προδιαγραφές

BrandDell
Model400-ANPB
PackagingBare Drive
InterfaceSATA 6.0Gb/s
Capacity8TB
RPM7200 RPM
Average Latency6Gb/s
Form Factor3.5"

Ερωτήσεις για αυτό το προϊόν

Does the Dell 400-ANPB 8TB 3.5" SATA drive ship with mounting screws, cables, or a tray, or must they be purchased separately?

The unit is supplied as a bare drive only; mounting hardware, SATA data and power cables, and any server-specific tray are not included and must be sourced separately.

Should I choose the 7.2K 6Gb/s version or a different spindle speed for a Dell PowerEdge server?

This model is the 7200 RPM 6Gb/s SATA variant; select it when the server bay and controller support 3.5" hot-swap SATA drives and the workload suits 7.2K performance.

What does the 6.0Gb/s SATA interface mean for actual throughput once the drive is installed in a PowerEdge server?

The 6.0Gb/s link caps burst transfer at 600 MB/s; sustained sequential reads and writes will be lower and are limited by the 7200 RPM mechanical speed.

Επίσης σε αυτό το ράφι

Οι πελάτες σύγκριναν και αυτά

Ίδιο ράφι, ίδιο ταμείο — οκτώ νομίσματα και κλείδωμα ισοτιμίας 30 λεπτών.