Δεχόμαστε κρυπτονομίσματα — έτσι ώστε αυτά που κατέχετε να μπορούν να αγοράσουν πραγματικό εξοπλισμό.Πληρώστε σε κρυπτονομίσματα, ξοδέψτε τα σε πραγματικό εξοπλισμό. Δωρεάν ασφαλισμένη αποστολή παγκοσμίως άνω των 399 $. Ουδέτερες κούτες αποστολής, χωρίς σήμανση, από τη Γερμανία.Δωρεάν ασφαλισμένη αποστολή άνω των 399 $. Η ισοτιμία σας κλειδώνει για 30 λεπτά μόλις ανοίξει το ταμείο.Κλείδωμα ισοτιμίας 30 λεπτών. Κάθε προϊόν είναι σφραγισμένο, ελεγμένο ως προς τον σειριακό αριθμό του, και καλύπτεται από εγγύηση 24 μηνών.Σφραγισμένο, με εγγύηση 24 μηνών.

Παρακολουθούμενα είδη Σύνδεση
LORDWORLD LX-15D serial bus servo with mounting bracket, metal gear housing, RGB status indicator on top

LORDWORLD

LORDWORLD LX-15D Serial Bus Servo with Bracket 15/17 kg·cm 240°

SKU CH-0K6V-HZB9S

Serial bus servo delivers 15 kg·cm at 6 V and 17 kg·cm at 7.4 V with 240° control angle, full metal gears, dual ball bearings and real-time position.

  • High torque of 15 kg·cm at 6 V rising to 17 kg·cm at 7.4 V
  • Real-time feedback on position temperature and voltage for precise control
  • RGB indicator blinks to warn of overcurrent over-temperature or locked-rotor
  • Full metal gears with dual ball bearings extend service life up to one month continuous
  • Serial bus interface lets you set control angle up to 240° and running speed

Robotics servo with 240° range

The LORDWORLD LX-15D is a serial bus servo built for RC robot projects and DIY automation. It delivers 15 kg/cm at 6 V and 17 kg/cm at 7.4 V with a controllable angle of 240°. Real-time feedback reports position, temperature and voltage, while an RGB indicator flashes on overcurrent, over-temperature or locked-rotor events. Full metal gears and dual ball bearings are fitted for accuracy and extended service life.

Sustained load behaviour

The unit is rated to run continuously for one month without interruption. Dual ball bearings, with one driving and one supporting, reduce wear during prolonged operation. The serial bus interface allows the control angle and running speed to be configured for the task. Real-time telemetry lets the host monitor temperature and voltage while the servo is under constant load.

Thermals, noise and power

An on-board RGB indicator blinks immediately when over-temperature or overcurrent conditions appear, giving instant visual warning. The servo operates at 6 V or 7.4 V, drawing higher current at the higher voltage to produce the 17 kg/cm torque figure. Full metal gearing and precision bearings keep mechanical noise low during normal movement.

Βασικά χαρακτηριστικά

  • High torque of 15 kg·cm at 6 V rising to 17 kg·cm at 7.4 V
  • Real-time feedback on position temperature and voltage for precise control
  • RGB indicator blinks to warn of overcurrent over-temperature or locked-rotor
  • Full metal gears with dual ball bearings extend service life up to one month continuous
  • Serial bus interface lets you set control angle up to 240° and running speed

Προδιαγραφές

BrandLORDWORLD

Ερωτήσεις για αυτό το προϊόν

Does the LX-15D's RGB indicator show heat or load warnings during continuous operation?

The RGB indicator blinks to signal overcurrent, over-temperature or locked-rotor conditions while the servo is running.

What controller interface is needed to command the LX-15D serial bus servo?

A serial bus controller that supports the servo's communication protocol is required to set angle, speed and read back position, temperature and voltage data.

Can the LX-15D share a serial bus with older servos that use a different protocol?

The LX-15D operates on its own serial bus protocol; mixing it with servos using other protocols on the same bus is not supported.

Επίσης σε αυτό το ράφι

Οι πελάτες σύγκριναν και αυτά

Ίδιο ράφι, ίδιο ταμείο — οκτώ νομίσματα και κλείδωμα ισοτιμίας 30 λεπτών.