Δεχόμαστε κρυπτονομίσματα — έτσι ώστε αυτά που κατέχετε να μπορούν να αγοράσουν πραγματικό εξοπλισμό.Πληρώστε σε κρυπτονομίσματα, ξοδέψτε τα σε πραγματικό εξοπλισμό. Δωρεάν ασφαλισμένη αποστολή παγκοσμίως άνω των 399 $. Ουδέτερες κούτες αποστολής, χωρίς σήμανση, από τη Γερμανία.Δωρεάν ασφαλισμένη αποστολή άνω των 399 $. Η ισοτιμία σας κλειδώνει για 30 λεπτά μόλις ανοίξει το ταμείο.Κλείδωμα ισοτιμίας 30 λεπτών. Κάθε προϊόν είναι σφραγισμένο, ελεγμένο ως προς τον σειριακό αριθμό του, και καλύπτεται από εγγύηση 24 μηνών.Σφραγισμένο, με εγγύηση 24 μηνών.

Παρακολουθούμενα είδη Σύνδεση
Five stainless steel V6 heat breaks with PTFE tubes, M6 and M7 threads, 1.75mm filament, 22.5mm long

Unique-Bargains

Unique-Bargains V6 Heat Break M6x22.5mm 1.75mm 5pc

SKU CH-49P4-6NFPD

Pack of five stainless-steel V6 heat breaks with M6/M7 threads, 22.5 mm length and PTFE tubing for 1.75 mm filament

  • Designed for 1.75mm filament printing
  • M7x1 middle and M6x1 base threads
  • 5mm throat length fits V6 hotends
  • Stainless steel resists heat and wear
  • Includes PTFE tube for smooth filament flow

V6 Heat Break 1.75mm Filament Compatibility

This pack supplies five stainless-steel heat breaks built for V6-style hot-ends that accept 1.75mm filament. Each throat measures 22.5mm long with a 4mm to 3mm internal bore and ships with a PTFE liner. The parts are intended for makers running PLA or ABS on compatible printers.

M7 and M6 Threaded Interface Requirements

The middle section carries an M7x1 thread while the base that seats in the heater block uses M6x1, so the surrounding heat sink and block must match both pitches. Installing the included PTFE tube completes the filament path and removes the need for a separate liner purchase. Builders whose hot-ends use a different thread pattern cannot use these throats.

Stainless Steel Body Under Continuous Extrusion

The stainless-steel construction resists deformation during long print jobs where the heat break sits at the thermal transition zone. Consistent filament flow depends on the PTFE liner staying seated and the threads remaining tight through repeated heat cycles. Printers that demand a longer throat or a different internal diameter will not match this 22.5mm design.

Βασικά χαρακτηριστικά

  • Designed for 1.75mm filament printing
  • M7x1 middle and M6x1 base threads
  • 5mm throat length fits V6 hotends
  • Stainless steel resists heat and wear
  • Includes PTFE tube for smooth filament flow

Προδιαγραφές

BrandUnique Bargains

Ερωτήσεις για αυτό το προϊόν

What is the throat length of these heat breaks?

Each heat break has a throat length of 22.5 mm, matching the standard V6 hot-end geometry.

How much heat does the stainless steel body transfer during long prints?

The stainless steel construction limits heat creep, keeping the cold zone cooler during extended printing sessions.

Which hot-end thread standard must my printer already use?

Your printer needs an M7×1 thread on the heat-sink side and an M6×1 thread into the heater block.

Επίσης σε αυτό το ράφι

Οι πελάτες σύγκριναν και αυτά

Ίδιο ράφι, ίδιο ταμείο — οκτώ νομίσματα και κλείδωμα ισοτιμίας 30 λεπτών.