LONGER
LONGER Laser Engraver Enclosure with Vent 27.5 x 27.5 x 13 inches
- Laser Engraver
69,99 $
0.00089466BTC
Διαθέσιμο
XTOOL
XTOOL Desktop Air Purifier for F1 285x190x296mm 55dB
Desktop air purifier with three-layer HEPA filtration removes 99.97% of laser fumes and odours, syncs automatically with the engraver, and runs at 55 dB in a compact 285×190×296 mm housing
- 3-layer filtration captures 99.97% of fumes and odours
- Pre-assembled unit syncs automatically with F1 laser engraver
- Compact 285x190x296 mm footprint fits any workspace
- Operates at 55 dB for quiet indoor use
- Simple filter replacement after three pre-filter changes
Desktop Air Purifier for xTool F1
The xTool Desktop Air Purifier is a dedicated fume extractor built exclusively for the xTool F1 laser engraver. It uses a 3-layer H13 HEPA filtration system that achieves a 99.97% purification rate to capture harmful gases and odours. The unit measures 285x190x296mm and operates at a maximum of 55dB. It is designed for indoor home, garage, basement, or workshop use.
Pre-assembled unit with one-click sync
The purifier arrives pre-assembled so no installation is required beyond connecting it to the engraver. Intelligent synchronisation lets the extractor start and stop automatically with the F1 via a single click. Filter maintenance is straightforward: the pre-filter is replaced after three uses, while the main filter cartridge swaps out without complicated disassembly. Buyers who need a purifier for larger-format engravers such as the F2 or M1 Ultra should verify compatibility before purchase.
3-layer filtration for F1 workloads
The H13 HEPA filter combines a pre-filter, activated charcoal odour absorber, and main HEPA layer to handle fumes and debris from typical F1 engraving and cutting jobs. It continuously pulls contaminants through all three stages during operation. The system is sized for the F1's output; extended heavy-duty sessions or materials producing exceptional volumes of smoke may saturate filters faster than the standard replacement interval.
Βασικά χαρακτηριστικά
- 3-layer filtration captures 99.97% of fumes and odours
- Pre-assembled unit syncs automatically with F1 laser engraver
- Compact 285x190x296 mm footprint fits any workspace
- Operates at 55 dB for quiet indoor use
- Simple filter replacement after three pre-filter changes
Προδιαγραφές
Δεν έχουν δημοσιευτεί ακόμη προδιαγραφές για αυτό το προϊόν.
Ερωτήσεις για αυτό το προϊόν
How do I confirm the purifier is filtering correctly after connecting it to my F1?
The unit starts and stops automatically with the F1 engraving process, so hearing the fan run during a job and seeing the 55 dB noise level indicates normal operation.
What comes in the box and which consumables must be purchased separately?
The purifier arrives pre-assembled with its 3-layer H13 HEPA filter installed; replacement pre-filters are sold separately and should be swapped after three are used.
Which capacity suits a desktop F1 setup — the 285×190×296 mm unit or a larger model?
The 285×190×296 mm purifier is the only model listed for the F1 series, delivering 99.97 % purification in a footprint that fits on a typical workbench.
Επίσης σε αυτό το ράφι
Οι πελάτες σύγκριναν και αυτά
Ίδιο ράφι, ίδιο ταμείο — οκτώ νομίσματα και κλείδωμα ισοτιμίας 30 λεπτών.
