Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Green circuit board with black memory chips, 288 gold pins, no heat spreader

A-Tech

A-Tech 4GB DDR4 3200 CL22 Desktop RAM M09707-001

SKU CH-3RJW-HBFY7

4 GB DDR4 desktop module running at 3200 MHz with CL22 latency and 1.2 V operation

  • Capacity4GB
  • SpeedDDR4 3200 (PC4 25600)
  • Tested Frequency3200
  • CAS LatencyCL22
  • Voltage1.20V
  • ECCNo
  • 4GB capacity lets you run more apps at once
  • DDR4 3200 speed keeps data moving at 3200 MT/s
  • CL22 latency gives quick response for everyday tasks
  • 20V operation matches standard DDR4 voltage for broad desktop compatibility
  • 288-pin DIMM form factor fits the HP M09707-001 slot exactly

4 GB DDR4 3200 Desktop Memory

This A-Tech module delivers four gigabytes of DDR4 memory at 3200 MT/s. It uses the standard 1.20 V operating voltage and an unbuffered, non-ECC design. The 288-pin DIMM form factor fits typical desktop motherboard slots. It is sold as a direct replacement for the HP part number M09707-001.

Suitable for HP desktop upgrades.

The module suits owners of compatible HP desktops that require a 3200 MT/s DDR4 DIMM with CL22 latency. Systems that demand ECC, registered or buffered memory will not accept this stick. Laptops and small-form-factor boards using 262-pin SO-DIMMs are also incompatible. Check your system documentation before ordering.

288-pin DDR4 DIMM with CL22 timing

The decisive specification is the 288-pin DDR4 DIMM interface combined with a CAS latency of 22. Only motherboards that support standard unbuffered DDR4 DIMMs at this pin count and timing can use the module. Verify the slot type and memory controller requirements to ensure a successful installation.

Põhijooned

  • 4GB capacity lets you run more apps at once
  • DDR4 3200 speed keeps data moving at 3200 MT/s
  • CL22 latency gives quick response for everyday tasks
  • 20V operation matches standard DDR4 voltage for broad desktop compatibility
  • 288-pin DIMM form factor fits the HP M09707-001 slot exactly

Tehnilised andmed

BrandA-Tech
SeriesCompatible Replacement for HP
ModelM09707-001
Capacity4GB
SpeedDDR4 3200 (PC4 25600)
Tested Frequency3200
CAS LatencyCL22
Voltage1.20V
ECCNo
Buffered/RegisteredUnbuffered
ChipsetMajor Brand Chipset
Heat SpreaderNo
FeaturesM09707-001
Recommend UseCompatible Replacement for HP M09707-001

Küsimused selle toote kohta

Will this module fit my HP desktop that uses the M09707-001 part number?

This module is built as a compatible replacement for HP part M09707-001 and uses the standard 288-pin DDR4 DIMM form factor used by current HP desktops.

My motherboard only supports 1.2 V DDR4 — is this module safe to install?

Yes, the module operates at the standard DDR4 voltage of 1.20 V, matching the requirement of any board that specifies 1.2 V DDR4 memory.

I have two free DIMM slots — can I add a second 4 GB stick later for dual-channel performance?

Absolutely; adding an identical 4 GB DDR4 3200 CL22 unbuffered module in the second slot will enable dual-channel operation on supported platforms.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.