Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Four clear acrylic tubes with 90-degree bends, 12mm diameter, 110mm and 415mm straight sections

Bitspower

Bitspower Pre-bent 90° Acrylic Hard Tube OD12mm 110x415mm 4-pack

SKU CH-K8AD-XV6ZY

Pre-bent 90° acrylic hard tubes with 110 mm and 415 mm straight sections, OD 12 mm, four pieces

  • TypeLiquid Cooling System
  • Pre-bent 90° angle removes the need for custom tube bending
  • 12 mm outer diameter fits standard hard-tube fittings
  • Acrylic construction provides clear coolant visibility
  • Each piece includes 110 mm and 415 mm straight sections for flexible trimming
  • Four tubes per pack covers multiple loop runs

Ready-to-install 90° hard tubes

The Bitspower Pre-bent 90° Acrylic Hard Tube set contains four OD12mm tubes curved at a 90-degree angle. Each piece includes straight sections of 110mm and 415mm on either side of the bend. They are designed to simplify custom water-cooling loops for both newcomers and experienced builders.

Cut-to-length capacity

The 110mm and 415mm straight segments give ample room to trim tubes to exact run lengths between components. Builders can handle tight corners and longer spans without heating or bending acrylic themselves. The fixed 90-degree radius limits routing to right-angle turns only.

Acrylic construction and fit

Clear acrylic tubing provides a rigid, glossy finish that shows coolant colour and flow. The OD12mm outer diameter matches standard compression fittings for secure, leak-free connections. Pre-bent shaping reduces the number of separate fittings needed for each corner.

Põhijooned

  • Pre-bent 90° angle removes the need for custom tube bending
  • 12 mm outer diameter fits standard hard-tube fittings
  • Acrylic construction provides clear coolant visibility
  • Each piece includes 110 mm and 415 mm straight sections for flexible trimming
  • Four tubes per pack covers multiple loop runs

Tehnilised andmed

TypeLiquid Cooling System

Küsimused selle toote kohta

Will the 12mm OD acrylic tubes fit my existing compression fittings?

Yes, the 12mm outer diameter matches standard G1/4 compression fittings made for 12mm hard tubing, so they connect directly to your current water blocks and radiators.

How can I verify the 90-degree bends are accurate after installation?

Pressure-test the loop; the pre-bent 90-degree angles should align cleanly with component ports without kinking, and the 110mm and 415mm straight sections let you measure clearance against your chassis.

Does the 4-pack include fittings or coolant, or must I buy them separately?

The box contains only four pre-bent 12mm acrylic tubes with 110mm and 415mm legs; fittings, coolant, and cutting tools are sold separately.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.