Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Green rectangular DDR4 memory module with gold contacts and black chips

Brute Networks

Brute Networks 8GB DDR4-2133 ECC Registered RDIMM 1Rx4 CL15 1.2V 288-Pin

SKU CH-JAPJ-MNHQ3

Adds 8 GB of DDR4 ECC registered memory at 2133 MHz CL15 1.2 V for HP-compatible servers

  • Capacity8GB
  • Type288-Pin DDR4 SDRAM
  • SpeedDDR4 2133 (PC4 17000)
  • CAS LatencyCL15
  • Voltage1.20V
  • ECCYes
  • ECC protection prevents data corruption with registered DDR4 design
  • 2133 MHz DDR4 speed handles demanding server workloads efficiently
  • 2 V operation reduces power consumption in dense configurations
  • 1Rx4 rank layout maximizes capacity per memory channel
  • HP 753220-S21 equivalent ensures drop-in compatibility for ProLiant servers

8GB DDR4-2133 ECC RDIMM

This 8GB DDR4-2133 registered DIMM adds error-correcting capacity to compatible HP server platforms. It targets administrators who need to expand memory in existing infrastructure without replacing the chassis. The module uses major-brand DRAM and matches the HP 753220-S21 specification for drop-in compatibility. It is not suited for desktop boards that require unbuffered non-ECC memory.

Registered ECC at 1.2 V

The stick runs at 1.20 V with a CL15 latency and a single 1Rx4 rank. Registered buffering reduces electrical load on the memory controller, helping stability when many modules are populated. ECC circuitry detects and corrects single-bit errors to protect data integrity in continuous workloads. Power draw scales with the number of populated slots rather than with a single high-wattage component.

288-pin DDR4 server upgrade

Installation requires a DDR4 RDIMM slot that supports 2133 MT/s operation and registered ECC modules. The 288-pin form factor fits standard server DIMM sockets and leaves other expansion bays unaffected. Builders who need higher densities or load-reduced LRDIMMs must select different modules. Systems limited to unbuffered memory cannot use this stick.

Põhijooned

  • ECC protection prevents data corruption with registered DDR4 design
  • 2133 MHz DDR4 speed handles demanding server workloads efficiently
  • 2 V operation reduces power consumption in dense configurations
  • 1Rx4 rank layout maximizes capacity per memory channel
  • HP 753220-S21 equivalent ensures drop-in compatibility for ProLiant servers

Tehnilised andmed

BrandHP
Capacity8GB
Type288-Pin DDR4 SDRAM
SpeedDDR4 2133 (PC4 17000)
CAS LatencyCL15
Voltage1.20V
ECCYes
Buffered/RegisteredRegistered
Rank1Rx4
ChipsetMajor Brand Chipset

Küsimused selle toote kohta

How do I install the 288-Pin DDR4 RDIMM in my server, and what step do people often miss?

Power down the server, open the chassis, align the notch on the 288-Pin module with the slot key, press firmly until both clips lock, then verify in BIOS that the 8GB module registers at 2133 MHz with ECC enabled.

What maintenance or replacement will the 8GB DDR4-2133 ECC Registered module need over its service life?

The module has no moving parts and requires no scheduled maintenance; replacement is only needed if a memory error persists after reseating or if a capacity upgrade is required.

What is the first limit that appears when the 1Rx4 CL15 1.2V RDIMM runs under sustained load?

The CAS latency of CL15 at 2133 MHz sets the timing floor; sustained throughput cannot exceed the PC4-17000 bandwidth ceiling of the module.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.