Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Two 20-inch 2-pin power switch cables with momentary push buttons

EN-Labs

EN-Labs PWSW50CM 2-Pin Power Switch Cable 20" 2-Pack motherboard accessory

SKU CH-AMZ0-B4SDV

Two 20-inch cables with 24 AWG UL-listed conductors and momentary push buttons connect to a motherboard 2-pin power switch header for power or reset functions

  • Connector Number2
  • Specifications24AWG UL Listed copper conductors
  • FeaturesPerfect fit for a motherboard's 2-pin power switch (Power SW
  • Fits standard motherboard power switch headers with 2-pin connector
  • Replaces broken case power or reset buttons without soldering
  • 20-inch cable length suits most chassis layouts
  • UL-listed 24AWG copper conductors ensure reliable signal
  • Two cables included for spare or dual-button builds

Simple front-panel control

This two-pack supplies a pair of 20-inch cables that plug directly onto a motherboard's 2-pin power-switch header. Each cable ends in a small momentary push-button so you can turn the system on or trigger a restart without shorting pins by hand. The set suits anyone building a test bench, repairing a broken case switch or wiring a custom enclosure.

Ready-to-use wiring

Conductors are 24AWG UL-listed copper and the connectors are pre-crimped, so no soldering or crimping tools are needed. The 20-inch length reaches most ATX and micro-ATX board layouts while leaving enough slack for cable routing behind the motherboard tray. Four colour variants exist; the pack ships with a random assortment.

Passive operation

The assembly draws no power of its own and adds no active cooling or noise to the build. Only the momentary button and the thin cable are present, so thermal impact inside the chassis is negligible. Installation is a simple press-fit onto the existing Power SW header.

Põhijooned

  • Fits standard motherboard power switch headers with 2-pin connector
  • Replaces broken case power or reset buttons without soldering
  • 20-inch cable length suits most chassis layouts
  • UL-listed 24AWG copper conductors ensure reliable signal
  • Two cables included for spare or dual-button builds

Tehnilised andmed

BrandEN-Lab
ModelPWSW50CM
Connector Number2
Specifications24AWG UL Listed copper conductors
FeaturesPerfect fit for a motherboard's 2-pin power switch (Power SW) header,this will also work as a restart switch. Great for replacing the power switch cable or for any weird project you might have in mind. Fit many cases. Works fine replacing the one that came with the computer case. Replacement for a broken or damaged power button switch/cable on a desktop computer Fits onto your motherboard power switch (Power SW) headers and features a small momentary-on (SPST) button. Very easy to install, and no soldering required. 24AWG UL listed copper conductors Cable length: 20 inches

Küsimused selle toote kohta

What type of motherboard header does the 2-pin power switch cable connect to?

The cable fits a motherboard's 2-pin Power SW header and can also serve as a restart switch.

What cable length and wire gauge are supplied?

Each cable is 20 inches long and uses 24AWG UL Listed copper conductors.

How is the switch installed and what common mistake should be avoided?

Press the momentary SPST button onto the two header pins; no soldering is needed, but reversing the two wires on a reset header will not trigger a restart.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.