Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Twinax breakout cable, QSFP+ to four SFP+ ends, 10 ft length

HPE Juniper Networking

HPE Juniper Networking QSFP+ to 4×SFP+ breakout cable 10 ft QFX3600

SKU CH-JMK0-P2G4T

A 10 ft twinaxial breakout cable splits one QSFP+ port into four SFP+ links for QFX3600 switches

  • QSFP+ to 4×SFP+ breakout splits one port into four 10 GbE links
  • 10 ft twinaxial copper cable reaches adjacent rack equipment without signal loss
  • 30 AWG conductors keep the assembly lightweight at 5.1 units for easy cable management
  • 100 Ohm impedance matches 10 Gigabit Ethernet signalling for reliable data integrity
  • Designed for QFX3600 switches ensuring plug-and-play compatibility in Juniper networks

QSFP+ to 4×SFP+ breakout cable for QFX3600

This Juniper Networks direct-attach copper cable splits one QSFP+ port into four SFP+ connections. It uses twinaxial wiring with 30 AWG conductors and 100 Ohm impedance. The assembly measures 10 ft end to end and is built for the QFX3600 switch series.

Suits QFX3600 deployments needing 10 GbE fan-out

Network engineers expanding port density on a QFX3600 will use this breakout to connect four SFP+ devices from a single QSFP+ uplink. It is not for buyers who need fibre connectivity, longer reach than 10 ft, or compatibility with non-QFX3600 platforms.

Verify QSFP+ and SFP+ port availability

Confirm the QFX3600 has a free QSFP+ port and that the four target devices accept SFP+ modules. Check that 10 ft of twinaxial cable fits the rack layout without exceeding bend-radius limits. Ensure the 30 AWG, 100 Ohm specification matches the link design.

Põhijooned

  • QSFP+ to 4×SFP+ breakout splits one port into four 10 GbE links
  • 10 ft twinaxial copper cable reaches adjacent rack equipment without signal loss
  • 30 AWG conductors keep the assembly lightweight at 5.1 units for easy cable management
  • 100 Ohm impedance matches 10 Gigabit Ethernet signalling for reliable data integrity
  • Designed for QFX3600 switches ensuring plug-and-play compatibility in Juniper networks

Tehnilised andmed

BrandAGILESTAR

Küsimused selle toote kohta

What switch port do I need free to plug the QSFP+ end of this breakout cable into a QFX3600?

A single QSFP+ port on the QFX3600 switch accepts the QSFP+ connector and splits the link into four 10 GbE SFP+ connections.

Can the four SFP+ legs connect to older 1 GbE SFP transceivers I already have?

The cable is built for 10 Gigabit Ethernet direct attach; 1 GbE SFP modules are not supported on these SFP+ interfaces.

How do I confirm each 10 GbE lane is up after I plug the SFP+ ends into my servers?

Check the QFX3600 port LEDs and run 'show interfaces terse' — each of the four channels should report link up at 10 Gbps with no errors.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.