Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Black 120mm square case fan with ARGB lighting and hydraulic bearing

Jungle Leopard

Jungle Leopard Prism6 PRO ARGB 120mm case fan Black 1600RPM 61.5CFM 2mmH2O HDB PWM 3/4 Pin

SKU CH-GBY3-WQ1FC

A 120 mm ARGB case fan with infinite-mirror lighting, hydraulic bearing, 1600 RPM and 61.5 CFM airflow

  • Fan Counts1 Fan
  • TypeCase Fan
  • CompatibilityCase
  • Fan Size120mm
  • Fan Thickness25mm
  • Bearing TypeHydraulic Bearing

Color Black Forward-1Pack

  • Infinite mirror ARGB lighting visible from any angle
  • Hydraulic bearing runs at 30 dBA for quiet cooling
  • PWM control adjusts speed from 765 to 1600 RPM
  • 5 CFM airflow with 2 mmH₂O static pressure
  • Standard 120 × 120 × 25 mm size fits most cases

120mm ARGB case fan with infinite mirror effect

The Jungle Leopard Prism6 PRO is a single 120mm case fan built for standard chassis mounts. It uses a hydraulic bearing and PWM control to vary speed between 765 and 1600 RPM. A three‑sided lens and back‑mounted LEDs create an infinite mirror ARGB effect that is visible from any angle when connected to a 5V 3‑pin header.

61.5 CFM airflow and 2 mmH₂O static pressure

At full speed the fan moves 61.5 CFM of air while generating 2 mmH₂O of pressure, enough for unrestricted case ventilation or a typical CPU cooler radiator. The rated noise level reaches 30 dBA at 1600 RPM, so acoustic output stays moderate. Headroom drops quickly when the fan faces dense fin stacks or restrictive filters.

3‑pin and 4‑pin power with 5V ARGB sync

The unit ships with both a 3‑pin and a 4‑pin power connector, letting it run on voltage or PWM headers. ARGB lighting requires a separate 5V 3‑pin motherboard or controller port; without that connection the LEDs remain off. Four self‑tapping screws are included for direct case or radiator mounting.

Põhijooned

  • Infinite mirror ARGB lighting visible from any angle
  • Hydraulic bearing runs at 30 dBA for quiet cooling
  • PWM control adjusts speed from 765 to 1600 RPM
  • 5 CFM airflow with 2 mmH₂O static pressure
  • Standard 120 × 120 × 25 mm size fits most cases

Tehnilised andmed

BrandJungle Leopard
SeriesPrism6 PRO
ModelJL Prism6 PRO BK
Fan Counts1 Fan
TypeCase Fan
CompatibilityCase
Fan Size120mm
Fan Thickness25mm
Bearing TypeHydraulic Bearing
RPM1600RPM
Air Flow61.5CFM
Air Pressure2mmH2O
Noise Level= 30dBA
Power Connector3 / 4 Pin
ColorBlack / White
LEDARGB
Dimensions120×120×25mm 4.72*4.72*0.98in

Selle mudeli teised versioonid

5 veel samast sarjast

Sama seeria, erinev mälumaht, jahutus või taktsagedus — võrrelge enne otsustamist.

Küsimused selle toote kohta

Will the 120 mm PWM fan run quietly on an older motherboard that only has 3-pin headers?

The fan uses a 3/4-pin connector so it fits a 3-pin header, but speed control becomes voltage-based instead of PWM; at full 1600 RPM the spec lists 30 dBA.

How can I confirm the ARGB lighting is functioning correctly after installation?

Connect the 3-pin 5 V ARGB header to a compatible motherboard or controller, then use the board's lighting software to verify the infinite-mirror effect cycles through colours and patterns.

Does the package include mounting hardware, or do I need to buy screws separately?

Four self-tapping screws are supplied in the box for direct case or radiator mounting; no additional fasteners are required.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.