Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
White Maxtor MTP-3207 thermal paste syringe 200g with grey cap

Maxtor

Maxtor MTP-3207 Thermal Paste 200g

SKU CH-0S57-MKHJX

A 200 g non-conductive thermal compound rated at 6 W/mk for CPUs, GPUs and consoles

  • Lowers CPU and GPU temperatures with 6 W/m·k conductivity
  • Non-conductive formula protects motherboards at >5.0 kV/mm breakdown voltage
  • Resists drying out with
  • 200 g syringe covers multiple CPU GPU and console installs
  • Ready for PS5 Xbox desktop laptop LED and PSU applications

Maxtor MTP-3207 200g Thermal Paste

This 200-gram tube of Maxtor MTP-3207 thermal compound delivers high-efficiency heat transfer for CPUs, GPUs and console processors. Its non-conductive formula protects sensitive electronics while maintaining stable temperatures across desktop, laptop and gaming hardware. The large volume suits system builders, repair technicians and enthusiasts who re-paste multiple devices.

Replacing dried or stock thermal compound

Swapping aged or factory-applied paste for this 6W/mk compound is worth it when temperatures climb under load or when reassembling a cooler after maintenance. The low volatility rate below .6% after 24 hours at 200°C means the material resists drying out, so the thermal interface stays effective longer than standard greases. It upgrades any application where the original compound has degraded or was applied too thinly.

Non-conductive paste for dense component layouts

With a breakdown voltage above 5.0 kV/mm, the grease can be spread confidently around exposed PCB components without risk of shorting adjacent pins. The 200g container provides enough material for dozens of CPU or GPU mounts, freeing you from buying single-use sachets for each job. It fits any build that needs a reliable, long-lasting thermal bridge between die and heatsink.

Põhijooned

  • Lowers CPU and GPU temperatures with 6 W/m·k conductivity
  • Non-conductive formula protects motherboards at >5.0 kV/mm breakdown voltage
  • Resists drying out with
  • 200 g syringe covers multiple CPU GPU and console installs
  • Ready for PS5 Xbox desktop laptop LED and PSU applications

Tehnilised andmed

Selle toote kohta ei ole veel tehnilisi andmeid avaldatud.

Küsimused selle toote kohta

What size syringe or container does the Maxtor MTP-3207 thermal paste come in?

The Maxtor MTP-3207 thermal paste is supplied in a 200g container, providing enough compound for multiple CPU and GPU applications.

How do I apply the Maxtor MTP-3207 paste correctly, and what common step should I avoid?

Clean both surfaces thoroughly, apply a small pea-sized dot or thin line onto the centre of the die, then mount the cooler straight down without spreading the paste manually, as manual spreading often traps air bubbles.

How often will I need to replace the Maxtor MTP-3207 thermal paste?

With a volatility rate below .6% after 24 hours at 200°C, the compound resists drying out for years, so replacement is typically only needed when you disassemble the cooler for upgrades or cleaning.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.