BFKK
BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
214,99 $
0.00276732BTC
Laos
NEMIX RAM
NEMIX RAM 16GB (2x8GB) DDR5 4800 CL40 1Rx8 1.1V UDIMM Dell Tower memory upgrade
A 16GB dual-channel DDR5 kit running at 4800MT/s with CL40 latency for Dell Tower desktops
- Capacity16GB (2 x 8GB)
- SpeedDDR5 4800 (PC5 38400)
- ECCNo
- Buffered/RegisteredUnbuffered
- ChipsetMajor OEM Samsung, Micron, Hynix
- Voltage1.10V
- 16 GB dual-channel kit expands Dell tower memory capacity
- DDR5 4800 MT/s speed delivers high data throughput for demanding tasks
- CL40 CAS latency supports responsive multitasking performance
- 1 V low voltage reduces system power draw
- 288-pin UDIMM form factor fits standard desktop memory slots
Dell Tower DDR5 upgrade
This 16GB kit contains two 8GB UDIMM modules built for Dell tower desktops that accept DDR5 memory. It targets owners who want a straightforward capacity increase without ECC or registered buffers. The 288-pin design matches standard desktop slots in compatible Dell systems.
Standard voltage thermals
Operating at 1.10V, the modules run at the JEDEC baseline for DDR5 and produce modest heat without a spreader. In typical desktop workloads the memory stays cool and silent because there are no moving parts. Power draw scales with the 4800 MT/s data rate and CL40 latency.
Sustained load behaviour
Under continuous read-write cycles the kit maintains its rated 4800 MT/s speed and CL40 timing at 1.10V. The 1Rx8 organisation keeps signal loading light on the memory controller during long sessions. Stability relies on the motherboard's DDR5 power management rather than on-board thermal sensors.
Põhijooned
- 16 GB dual-channel kit expands Dell tower memory capacity
- DDR5 4800 MT/s speed delivers high data throughput for demanding tasks
- CL40 CAS latency supports responsive multitasking performance
- 1 V low voltage reduces system power draw
- 288-pin UDIMM form factor fits standard desktop memory slots
Tehnilised andmed
| Brand | NEMIX RAM |
|---|---|
| Series | NEMIX RAM Original Series Memory |
| Model | DDR5 Non-ECC Unbuffered UDIMM Memory |
| Part Number | MD38400-818K2 |
| Capacity | 16GB (2 x 8GB) |
| Speed | DDR5 4800 (PC5 38400) |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Voltage | 1.10V |
| Compatible System | Dell |
| CAS Latency | CL40 |
| Heat Spreader | No |
| Type | 288-Pin DDR5 UDIMM |
| Rank | 1Rx8 |
| Features | DDR5 Non-ECC Unbuffered UDIMM Motherboard Compatible |
| Package Content | 16GB (2 x 8GB) DDR5 4800MHz PC5-38400 1Rx8 1.1V 288-PIN Non-ECC UDIMM KIT |
Küsimused selle toote kohta
How do I install the 288-pin DDR5 UDIMM modules in my Dell tower, and which step is often missed?
Power off and unplug the tower, open the case, align each module's notch with the slot key, press firmly until both retention clips click, then verify in BIOS that both 8 GB sticks are detected at 4800 MT/s.
What maintenance or replacement will this 16 GB DDR5 kit need over time?
No scheduled maintenance is required; the modules have no heat spreader and run at 1.10 V, so only replace them if a stick fails or you need more capacity.
What limit appears first when the 1Rx8 CL40 memory runs under sustained load?
The CAS latency of CL40 at 4800 MT/s sets the primary timing ceiling; sustained workloads will hit that latency bound before any thermal or voltage limit.
Veel samast osakonnast
Kliendid võrdlesid neid ka
Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.
