Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Green rectangular circuit board with black memory chips and gold edge connectors

OWC

OWC 4GB DDR4 2400MHz CL17 1.2V 288pin UDIMM 2U4D41R804GB

SKU CH-P1R1-HV9XA

A 4GB DDR4 2400MHz UDIMM module for HP ProDesk 400 G4 and 600 G3 desktops

  • Capacity4GB
  • Type288-Pin DDR4 Non-ECC UDIMM
  • SpeedDDR4 2400 (PC4 19200)
  • CAS LatencyCL17
  • Voltage1.2V
  • ECCNo
  • Boosts HP ProDesk 400 G4 and 600 G3 responsiveness
  • 4GB DDR4 2400MHz CL17 module installs easily
  • Low 1.2V operation cuts power draw
  • JEDEC compliant for warranty-safe upgrades
  • Backward compatible with 2133MHz systems

HP ProDesk upgrade module

This 4 GB DDR4 UDIMM is built for HP ProDesk 400 G4 and 600 G3 small-form-factor and tower systems. It adds memory capacity without requiring ECC or registered buffers. The unbuffered design keeps installation straightforward for compatible desktops and workstations. Buyers who need ECC error correction or higher-density modules should look elsewhere.

Sustained-load stability

Rated at 2400 MHz with CL17 latency and 1.2 V operation, the module meets JEDEC PC4-19200 specifications for steady throughput. It also runs at 2133 MHz when the platform requires a lower speed. The single-rank 1Rx8 organisation delivers consistent bandwidth during extended workloads. Systems that demand voltages other than 1.2 V or speeds above 2400 MHz will not benefit from this part.

Tool-free DIMM installation

The 288-pin edge connector seats directly into standard DDR4 UDIMM slots; no heat spreader means a low profile that fits tight SFF chassis. Alignment notches prevent backwards insertion, and the unbuffered layout avoids register-related POST failures. Builders who cannot access the motherboard slots or who need registered memory will find this module unsuitable.

Põhijooned

  • Boosts HP ProDesk 400 G4 and 600 G3 responsiveness
  • 4GB DDR4 2400MHz CL17 module installs easily
  • Low 1.2V operation cuts power draw
  • JEDEC compliant for warranty-safe upgrades
  • Backward compatible with 2133MHz systems

Tehnilised andmed

BrandOWC
Part Number2U4D41R804GB
Capacity4GB
Type288-Pin DDR4 Non-ECC UDIMM
SpeedDDR4 2400 (PC4 19200)
CAS LatencyCL17
Voltage1.2V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
Heat SpreaderNo
Compatible SystemHP ProDesk 400 G4 SFF
HP ProDesk 400 G4 Tower
HP ProDesk 600 G3 SFF
HP ProDesk 600 G3 Tower

Selle mudeli teised versioonid

5 veel samast sarjast

Sama seeria, erinev mälumaht, jahutus või taktsagedus — võrrelge enne otsustamist.

Küsimused selle toote kohta

Does the 1.2V DDR4 module run hot or draw extra power in an HP ProDesk 400 G4 SFF that stays on all day?

The stick operates at the standard 1.2V JEDEC voltage and has no heat spreader, so it adds minimal heat and power draw inside the small-form-factor chassis.

What must the HP ProDesk 600 G3 Tower already have for this 288-pin UDIMM to work?

The system needs a free DDR4 DIMM slot that accepts 2400MHz PC4-19200 unbuffered non-ECC memory; the module is single-rank 1Rx8 and requires no extra hardware.

Will this 2400MHz CL17 kit down-clock reliably beside existing 2133MHz sticks in an HP ProDesk 400 G4 Tower?

Yes, the module is backward compatible with 2133MHz operation, so it will match the slower JEDEC speed and timings of the installed memory automatically.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.