Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Black 60 by 25 mm case fan with four pin PWM connector

Zyvpee

Zyvpee DS06025B12L 60mm 25mm 4-pin PWM case fan

SKU CH-BHF6-X2WVW

A 60mm ball-bearing PWM case fan running at 12V with a 4-pin connector

  • TypeCase Fan
  • Bearing TypeBall
  • Power Connector4 Wires
  • ColorBlack
  • LEDNon-LED
  • Dimensions60*25mm
  • PWM 4-pin speed control adapts to thermal load
  • Ball bearing reduces friction for longer service life
  • 60 mm × 25 mm frame fits tight chassis slots
  • 12 V 0.3 A draw keeps power budget low
  • Non-LED black design stays invisible inside the case

Compact 60 mm PWM fan for tight builds

This 60 mm by 25 mm case fan uses a four-pin PWM connector so the motherboard can vary speed automatically. It runs on 12 V DC and draws 0.3 A, making it suitable for small-form-factor cases or as a targeted spot-cooling device. The ball bearing and black frame are designed for continuous operation without LED lighting.

Steady airflow under constant load

Because the motor is rated for 12 V at 0.3 A, the fan maintains its PWM curve during extended sessions rather than throttling back after a short burst. The ball bearing reduces friction over time, helping the rotor keep a consistent speed when the system stays under load for hours. No lighting means no extra heat from LEDs.

Check mounting points and header type

Verify that your chassis has 60 mm screw holes spaced for a 25 mm thick frame before ordering. Confirm the motherboard or fan controller provides a four-pin PWM header; a three-pin header will run the fan at full speed only. Ensure the 12 V supply can deliver the stated current for each fan you install.

Põhijooned

  • PWM 4-pin speed control adapts to thermal load
  • Ball bearing reduces friction for longer service life
  • 60 mm × 25 mm frame fits tight chassis slots
  • 12 V 0.3 A draw keeps power budget low
  • Non-LED black design stays invisible inside the case

Tehnilised andmed

Brand3ccooler.com
SeriesDS06025B12L P017
ModelDS06025B12L
TypeCase Fan
Bearing TypeBall
Power Connector4 Wires
ColorBlack
LEDNon-LED
Dimensions60*25mm

Küsimused selle toote kohta

How does the 60 mm ball-bearing fan behave when running continuously at 12 V and 0.3 A?

The fan draws 0.3 A at 12 V through its 4-pin PWM connector, so speed and noise scale with the motherboard curve; the ball bearing is rated for long-term continuous operation.

What motherboard header or controller is required to run the 4-pin PWM connector?

A standard 4-pin PWM fan header on the motherboard or a compatible fan controller supplies the 12 V power and the PWM signal needed for speed regulation.

Will the 60×25 mm frame and 4-pin PWM connector fit alongside older 3-pin fans on the same controller?

The 60×25 mm frame matches the 6025 mounting pattern, and the 4-pin connector works in 3-pin headers at full speed, so it can share a controller with legacy fans.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.