Elfogadjuk a kriptovalutát — így az Ön birtokában lévő érmékből valódi hardvert vásárolhat.Fizessen kriptóval, és költse el valódi hardverre. 399 $ felett világszerte díjmentes a biztosított szállítás. Egyszerű, jelöletlen külső kartonok, Németországból küldve.399 $ felett díjmentes a biztosított szállítás. Az Ön árfolyama a pénztár megnyitásától számított 30 percre zárolva marad.Árfolyam zárolva 30 percre. Minden termék gyárilag zárt, sorozatszáma ellenőrzött, és 24 hónapos garancia fedezi.Zárt csomagolás, 24 hónap garancia.

Árfigyelő lista Bejelentkezés
Small green circuit board with a black 2.5 inch SATA female socket and a 44 pin IDE male connector

Corn Electronics

Corn Electronics SATA to IDE Adapter Converter 1.5Gb/s 2.5" SATA Female to 3.5" IDE Male 44 Pin

SKU CH-PBEW-0B6QS

Converts 2.5" SATA drives to 3.5" 44-pin IDE for legacy systems at 1.5 Gb/s

  • Connect 2.5" SATA drives to 3.5" IDE systems via 44-pin male connector
  • Achieve 1.5 Gb/s transfer speeds compliant with Serial ATA 1.0 specification
  • Install instantly with no drivers required across DOS Windows 98 to Windows 7 and Linux
  • Compact 69 mm by 14 mm PCB fits tight spaces without extra cables
  • Convert SATA HDDs SSDs and optical drives into standard 3.5" IDE devices

SATA-to-IDE adapter for 2.5" drives

This Corn Electronics adapter converts a 2.5-inch SATA hard drive or optical device into a 3.5-inch 44-pin IDE device. It suits repair technicians or hobbyists maintaining legacy desktops or industrial systems that still rely on 44-pin IDE interfaces. The compact PCB measures 69mm by 14mm and requires no external cables for the SATA connection.

Transfer rate limited to 1.5 Gb/s

The adapter complies with Serial ATA specification revision 1.0 and supports a maximum data transfer rate of 1.5 Gb/s (150 MB/s). It also supports ATA 133 and ATA 100 standards on the IDE side. This bandwidth ceiling makes it unsuitable for modern SSDs or high-throughput applications that demand faster SATA revisions.

Driver-free installation with hot-swap limitation

Installation is straightforward: plug the 7+15-pin female SATA connector directly into the drive and insert the 44-pin male IDE connector into the host socket. No drivers are required for DOS, Windows 98 through Windows 7, or Linux. The adapter does not support hot-swap operation, so the system must be powered down before connecting or disconnecting drives.

Erősségek

  • Connect 2.5" SATA drives to 3.5" IDE systems via 44-pin male connector
  • Achieve 1.5 Gb/s transfer speeds compliant with Serial ATA 1.0 specification
  • Install instantly with no drivers required across DOS Windows 98 to Windows 7 and Linux
  • Compact 69 mm by 14 mm PCB fits tight spaces without extra cables
  • Convert SATA HDDs SSDs and optical drives into standard 3.5" IDE devices

Műszaki adatok

Ehhez a termékhez egyelőre nincs közzétett műszaki adat.

Kérdések a termékről

What does the 1.5 Gb/s transfer rate mean for a drive connected through this adapter?

The adapter complies with Serial ATA revision 1.0 and caps throughput at 1.5 Gb/s (150 MB/s), so any SATA drive attached will run at that speed even if the drive itself is faster.

Which IDE standard does the 44-pin connector support and what does that limit?

The 44-pin male connector supports ATA-133 and ATA-100 modes, so the maximum parallel IDE transfer rate is 133 MB/s, but the SATA side remains limited to 1.5 Gb/s.

Will this 69 mm × 14 mm board fit inside a standard 3.5-inch drive bay?

The PCB measures 69 mm by 14 mm and plugs directly into a 44-pin IDE header; it is designed to sit on a 2.5-inch SATA drive and occupy the space of a 3.5-inch device without extra cables.

Szintén ezen a polcon

Vásárlók ezeket hasonlították össze

Ugyanaz a polc, ugyanaz a pénztár — nyolc pénznem és 30 perces árfolyamzár.