Elfogadjuk a kriptovalutát — így az Ön birtokában lévő érmékből valódi hardvert vásárolhat.Fizessen kriptóval, és költse el valódi hardverre. 399 $ felett világszerte díjmentes a biztosított szállítás. Egyszerű, jelöletlen külső kartonok, Németországból küldve.399 $ felett díjmentes a biztosított szállítás. Az Ön árfolyama a pénztár megnyitásától számított 30 percre zárolva marad.Árfolyam zárolva 30 percre. Minden termék gyárilag zárt, sorozatszáma ellenőrzött, és 24 hónapos garancia fedezi.Zárt csomagolás, 24 hónap garancia.

Árfigyelő lista Bejelentkezés
Green circuit board with screw terminals and pin headers

LORDWORLD

LORDWORLD ADS1263 10-Ch 32-Bit ADC HAT Development Board

SKU CH-JPBB-X7CXM

A 10-channel 32-bit ADC HAT with 38.4 kSPS sampling, 24-bit auxiliary ADC, 2.5 V reference, PGA up to 32×, screw terminals and RTD support for Raspberry Pi and Jetson Nano

  • 10-channel 32-bit ADC captures fine signal detail
  • 5 differential inputs reject common-mode noise
  • 4 kSPS maximum sampling rate suits fast measurements
  • Onboard screw terminals and Waveshare-compatible header simplify sensor wiring
  • Built-in 24-bit auxiliary ADC, PGA up to 32× and 2.5 V reference extend dynamic range

Precision ADC HAT for Raspberry Pi and Jetson Nano

The LORDWORLD ADS1263 board adds a 10-channel 32-bit analogue-to-digital converter to Raspberry Pi series and Jetson Nano platforms. It uses the ADS1263 chip for low noise and low temperature drift with a maximum sampling rate of 38.4 kSPS. An embedded 24-bit auxiliary ADC and programmable gain up to 32 times extend measurement flexibility. The board targets developers who need high-resolution data acquisition for sensors or instrumentation.

Header and terminal interfaces for sensor

An onboard AD header matches the Waveshare sensor pinout for direct module connection while a screw terminal block accepts generic analogue signals and power. A separate control header allows the module to be driven by hosts other than the Raspberry Pi. Eight multiplexed GPIO pins provide additional digital I/O. Builds requiring wireless connectivity or on-board signal conditioning beyond the provided PGA must add those functions externally.

Low-drift operation with internal 2.5 V reference

The ADS1263 delivers low temperature drift and low noise using a 2.5 V internal reference voltage and an internal test signal for verification. A three-wire RTD circuit can be enabled by soldering a 0R resistor for precision temperature sensing. IDAC current sources support resistive sensor excitation. The board draws power from the host platform and adds minimal thermal load in normal use.

Erősségek

  • 10-channel 32-bit ADC captures fine signal detail
  • 5 differential inputs reject common-mode noise
  • 4 kSPS maximum sampling rate suits fast measurements
  • Onboard screw terminals and Waveshare-compatible header simplify sensor wiring
  • Built-in 24-bit auxiliary ADC, PGA up to 32× and 2.5 V reference extend dynamic range

Műszaki adatok

BrandLORDWORLD

Kérdések a termékről

How many differential channels does the ADS1263 provide for sustained high-precision capture?

The ADS1263 chip delivers 5 differential input channels at 32-bit resolution with a maximum sampling rate of 38.4 kSPS.

What is the onboard reference voltage and does the board generate noticeable heat during continuous operation?

A 2.5 V internal reference is built in; the ADS1263 is specified for low noise and low temperature drift, so heat remains minimal during all-day sampling.

Which host boards can drive this HAT without extra adapters?

The HAT fits Raspberry Pi series boards and Jetson Nano directly via the 40-pin GPIO header.

Szintén ezen a polcon

Vásárlók ezeket hasonlították össze

Ugyanaz a polc, ugyanaz a pénztár — nyolc pénznem és 30 perces árfolyamzár.