Elfogadjuk a kriptovalutát — így az Ön birtokában lévő érmékből valódi hardvert vásárolhat.Fizessen kriptóval, és költse el valódi hardverre. 399 $ felett világszerte díjmentes a biztosított szállítás. Egyszerű, jelöletlen külső kartonok, Németországból küldve.399 $ felett díjmentes a biztosított szállítás. Az Ön árfolyama a pénztár megnyitásától számított 30 percre zárolva marad.Árfolyam zárolva 30 percre. Minden termék gyárilag zárt, sorozatszáma ellenőrzött, és 24 hónapos garancia fedezi.Zárt csomagolás, 24 hónap garancia.

Árfigyelő lista Bejelentkezés
Small green circuit board with USB-C port and pre-soldered header pins

LORDWORLD

LORDWORLD RP2040-Zero Development Board USB-C Pre-soldered Headers

SKU CH-RHBP-0S9VK

Pico-compatible RP2040 board with dual-core 133 MHz processor, 264 KB SRAM, 2 MB flash, USB-C and pre-soldered headers for immediate prototyping

  • RP2040 microcontroller designed in the United Kingdom
  • Dual-core Arm Cortex M0+ processor running up to 133 MHz
  • 264KB SRAM with 2MB on-board Flash memory
  • USB-C connector for modern, easier connectivity
  • Castellated module allows direct soldering to carrier boards

Compact RP2040 board for embedded prototyping

The LORDWORLD RP2040-Zero is a microcontroller development board built around the Raspberry Pi RP2040 chip. It targets hobbyists, students and engineers who need a small, low-cost platform for learning, sensor interfaces or custom IoT edge devices. The pre-soldered headers and USB-C connector make it ready for immediate breadboard use without additional assembly.

Sustained operation within microcontroller limits

The dual-core Arm Cortex M0+ processor runs at up to 133 MHz with 264KB of SRAM and 2MB of on-board flash. Under continuous load the chip remains in its designed thermal envelope without active cooling. Low-power sleep and dormant modes allow battery-powered projects to idle for extended periods while retaining state.

Castellated edges and USB-C for flexible integration

Castellated module edges enable direct soldering to carrier boards for permanent installations. The USB-C port provides a modern, reversible connection for power and drag-and-drop programming via mass storage. USB 1.1 device and host support permits simple peripheral communication such as keyboards or flash drives.

Erősségek

  • RP2040 microcontroller designed in the United Kingdom
  • Dual-core Arm Cortex M0+ processor running up to 133 MHz
  • 264KB SRAM with 2MB on-board Flash memory
  • USB-C connector for modern, easier connectivity
  • Castellated module allows direct soldering to carrier boards

Műszaki adatok

BrandLORDWORLD

Kérdések a termékről

Does the RP2040 chip run hot or draw much power when left running all day?

The dual-core Arm Cortex M0+ processor runs up to 133 MHz and includes low-power sleep and dormant modes to keep heat and power draw minimal during continuous operation.

What must I already have to start using the USB-C connector and pre-soldered headers?

You need a USB-C cable and a computer to access the drag-and-drop mass-storage programming interface; no separate debugger or power supply is required.

Can I keep my older USB 1.1 peripherals when adding this board?

Yes, the board provides USB 1.1 device and host support so legacy peripherals can communicate directly with the RP2040 microcontroller.

Szintén ezen a polcon

Vásárlók ezeket hasonlították össze

Ugyanaz a polc, ugyanaz a pénztár — nyolc pénznem és 30 perces árfolyamzár.