Elfogadjuk a kriptovalutát — így az Ön birtokában lévő érmékből valódi hardvert vásárolhat.Fizessen kriptóval, és költse el valódi hardverre. 399 $ felett világszerte díjmentes a biztosított szállítás. Egyszerű, jelöletlen külső kartonok, Németországból küldve.399 $ felett díjmentes a biztosított szállítás. Az Ön árfolyama a pénztár megnyitásától számított 30 percre zárolva marad.Árfolyam zárolva 30 percre. Minden termék gyárilag zárt, sorozatszáma ellenőrzött, és 24 hónapos garancia fedezi.Zárt csomagolás, 24 hónap garancia.

Árfigyelő lista Bejelentkezés
Green PCB adapter board with ATX 24-pin, CPU 4+4-pin, SATA, IDE and DC 5525 connectors, 12.6in DC cable

myVolts

myVolts LD-A250WL 12V 250W power supply

SKU CH-ATCC-MEERJ MPN LD-A250WL

A 250 W AT power adapter board converts 12 V input into multiple rails with overcurrent and short-circuit protection, and includes ATX, CPU, SATA, IDE and DC connectors for compact builds

  • TypeAT
  • Saves case space by plugging ATX connector directly onto motherboard eliminating 24 wires
  • Delivers stable power with 250W output across five rails including +12V at 16A
  • Protects components with overcurrent and short-circuit shutdown on all main rails
  • Fits tight builds with short cables: 320mm DC, 210mm CPU, 200mm IDE, 150mm SATA
  • Runs reliably from -5 to 55°C with built-in oscillator at 250-350 kHz

Adapter board for low-power ATX builds

The myVolts LD-A250WL is a 250 W adapter board that accepts a single 12 V DC input and delivers five regulated rails through an ATX 24-pin, a CPU 4+4-pin, one SATA, one IDE and a DC 5525 connector. Cable lengths are fixed at 320 mm for DC, 210 mm for CPU, 200 mm for IDE and 150 mm for SATA. Over-current and short-circuit protection shut down the outputs when limits are exceeded.

Suits compact systems needing a small ATX power

Builders of mini PCs, HTPCs, POS terminals, ITX cases, web servers or industrial controllers that run from a 12 V source will fit this board into tight spaces. It is not for systems that require more than 250 W total draw, need additional PCIe or EPS connectors, or must operate from an AC mains input without an external brick.

250 W total power rating from 12 V input

The board supplies up to 16 A on the +12 V rail, 6 A each on +5 V and +3.3 V, 2 A on +5 VSB and 0.05 A on -12 V, with an operating temperature range of -5 °C to 55 °C. If the combined load of all components exceeds 250 W, the protection circuits will shut the unit down.

Erősségek

  • Saves case space by plugging ATX connector directly onto motherboard eliminating 24 wires
  • Delivers stable power with 250W output across five rails including +12V at 16A
  • Protects components with overcurrent and short-circuit shutdown on all main rails
  • Fits tight builds with short cables: 320mm DC, 210mm CPU, 200mm IDE, 150mm SATA
  • Runs reliably from -5 to 55°C with built-in oscillator at 250-350 kHz

Műszaki adatok

TypeAT

Kérdések a termékről

Will the over-current protection on the +12V 16A rail need resetting after it trips?

The protection turns the output off when peak current is reached; the board must be power-cycled to restore operation.

Which rail hits its limit first in a sustained 250W load?

The +12V rail at 16A reaches its maximum before the +5V 6A or +3.3V 6A rails under continuous draw.

How hot does the PCB get when running all day at 55°C ambient?

The board is rated for operation up to 55°C with 45–75% humidity; no active cooling is included, so case airflow must keep the PCB within that range.

Szintén ezen a polcon

Vásárlók ezeket hasonlították össze

Ugyanaz a polc, ugyanaz a pénztár — nyolc pénznem és 30 perces árfolyamzár.