Priimame kriptovaliutą — taip monetos, kurias turite, gali nupirkti tikrą techniką.Mokėkite kriptovaliuta, išleiskite ją tikrai technikai. Nemokamas apdraustas pristatymas visame pasaulyje virš 399 $. Paprastos, be žymų siuntos dėžės, siunčiamos iš Vokietijos.Nemokamas apdraustas pristatymas virš 399 $. Jūsų kursas fiksuojamas 30 minučių, kai tik prasideda atsiskaitymas.Kursas fiksuojamas 30 minučių. Kiekvienas gaminys užplombuotas, jo serijos numeris patikrintas, ir jam taikoma 24 mėnesių garantija.Užplombuota, 24 mėnesių garantija.

Stebimos prekės Prisijungti
Silver 3.5-inch internal hard drive with Fibre Channel connector

HPE

HPE AP729A StorageWorks 450 GB 10000 rpm Fibre Channel SAN hard drive

SKU CH-FDF1-C0BK8

A 450 GB internal SAN hard drive spinning at 10000 rpm with a Fibre Channel interface and hot-swap capability

  • TypeSAN Hard Drive
  • 450 GB capacity stores large datasets
  • 10000 rpm spindle speed delivers fast data access
  • Fibre Channel interface connects to SAN environments
  • Hot-swappable design allows drive replacement without downtime
  • Lightweight 1 lb construction simplifies installation

HPE AP729A 450 GB Fibre Channel SAN Drive

The HPE AP729A is a 450 GB internal hard drive built for StorageWorks SAN environments. It spins at 10000 rpm and uses a Fibre Channel interface to deliver block-level storage for enterprise arrays. The drive is hot-swappable, allowing replacement without powering down the enclosure. It targets administrators who need reliable capacity inside a qualified HP hardware stack.

Verify Fibre Channel Backplane

Before ordering, confirm that your storage array or server backplane accepts Fibre Channel drives with the correct connector pin-out. Check that the hot-swap caddy or carrier supplied with your chassis matches the drive form factor. Ensure the SAN controller firmware lists the AP729A as a supported spare. Validate that the existing drive bay provides adequate airflow for a 10000 rpm unit.

Sustained Throughput In Continuous Array Workloads

Under sustained load the 10000 rpm spindle maintains consistent rotational latency for sequential and random I/O patterns typical of database volumes. Hot-swap capability lets a failed unit be replaced while the array continues serving data without interruption. The Fibre Channel link preserves deterministic latency during extended rebuild or backup windows. Mechanical wear follows enterprise duty-cycle ratings for always-on operation.

Privalumai

  • 450 GB capacity stores large datasets
  • 10000 rpm spindle speed delivers fast data access
  • Fibre Channel interface connects to SAN environments
  • Hot-swappable design allows drive replacement without downtime
  • Lightweight 1 lb construction simplifies installation

Specifikacijos

BrandHPE
TypeSAN Hard Drive

Klausimai apie šią prekę

Does the HPE AP729A ship with any cables, brackets or a tray, or must those be purchased separately?

The unit is an internal hot-swappable drive weighing about 1 lb; no cables, brackets or tray are mentioned in the specifications, so plan to source any required mounting hardware or Fibre Channel cables separately.

The part number AP729A shows 450 GB at 10000 rpm — are there other capacity or speed versions under the same model?

The supplied data lists only the 450 GB, 10000 rpm configuration for part number AP729A; no alternative capacities or spindle speeds are referenced for this specific model.

What does the 10000 rpm spindle speed mean for actual throughput when the drive is installed in a Fibre Channel SAN?

A 10000 rpm Fibre Channel drive typically delivers higher sustained transfer rates and lower average latency than slower-spinning disks, improving random I/O performance in a SAN environment.

Taip pat šiame skyriuje

Kiti pirkėjai taip pat lygino

Ta pati lentyna, tas pats atsiskaitymas — aštuonios monetos ir 30 minučių fiksuotas kursas.