Priimame kriptovaliutą — taip monetos, kurias turite, gali nupirkti tikrą techniką.Mokėkite kriptovaliuta, išleiskite ją tikrai technikai. Nemokamas apdraustas pristatymas visame pasaulyje virš 399 $. Paprastos, be žymų siuntos dėžės, siunčiamos iš Vokietijos.Nemokamas apdraustas pristatymas virš 399 $. Jūsų kursas fiksuojamas 30 minučių, kai tik prasideda atsiskaitymas.Kursas fiksuojamas 30 minučių. Kiekvienas gaminys užplombuotas, jo serijos numeris patikrintas, ir jam taikoma 24 mėnesių garantija.Užplombuota, 24 mėnesių garantija.

Stebimos prekės Prisijungti
Small green circuit board with USB-C connector and three LEDs

LORDWORLD

LORDWORLD PL2303 USB-C UART Module

SKU CH-6VHF-9053H

USB-C to UART adapter with PL2303GS chip, jumper-selectable 1.8V to 5V logic levels and TX, RX, power LEDs

  • PL2303GS chip provides modern USB-C UART connectivity
  • Three LED indicators show TXD, RXD and power status instantly
  • Jumper-selectable VCCIO delivers 5 V or 3.3 V output directly
  • Open jumper mode powers module from target board at 1.8 V, 2.5 V, 3.3 V or 5 V
  • Broad Windows support from XP through 11 ensures driver compatibility

USB-C UART bridge for makers

The LORDWORLD PL2303 module converts a USB-C port into a TTL serial link. It is built around the PL2303GS chip and targets developers, hobbyists and repair technicians who need a compact adapter for microcontrollers, routers or embedded consoles.

Selectable logic levels cover 1.8V to 5V

A three-position jumper sets the I/O voltage to 5 V, 3.3 V or passes target-board power for 1.8 V and 2.5 V operation. This range handles most common logic families, but the single-channel design cannot drive multiple independent buses at once.

Low-power USB-C operation with status LEDs

The board draws bus power and stays cool during typical debug sessions. Three onboard LEDs show TXD, RXD and power activity, giving immediate visual feedback without extra instrumentation.

Privalumai

  • PL2303GS chip provides modern USB-C UART connectivity
  • Three LED indicators show TXD, RXD and power status instantly
  • Jumper-selectable VCCIO delivers 5 V or 3.3 V output directly
  • Open jumper mode powers module from target board at 1.8 V, 2.5 V, 3.3 V or 5 V
  • Broad Windows support from XP through 11 ensures driver compatibility

Specifikacijos

BrandLORDWORLD

Klausimai apie šią prekę

Will the PL2303GS chip on this module talk to my 5 V Arduino without a level shifter?

Yes — set the jumper to VCCIO-5V and the module drives 5 V logic on TXD and RXD, matching the Arduino directly.

How do I know the USB-C link is alive once I plug it in?

The PWR LED lights when the host enumerates the device; TXD and RXD blink during actual data transfer so you can see traffic immediately.

Does the board ship with a USB-C cable and jumper shunt, or must I source them?

The module includes the fitted jumper header for VCCIO selection; a USB-C cable is not included and must be supplied separately.

Taip pat šiame skyriuje

Kiti pirkėjai taip pat lygino

Ta pati lentyna, tas pats atsiskaitymas — aštuonios monetos ir 30 minučių fiksuotas kursas.