Mēs pieņemam kriptovalūtu — lai tā, kas Jums pieder, varētu nopirkt īstu aparatūru.Maksājiet kriptovalūtā, iztērējiet to īstai aparatūrai. Bezmaksas apdrošināta piegāde visā pasaulē virs 399 $. Vienkāršas, nemarķētas kastes, sūtītas no Vācijas.Bezmaksas apdrošināta piegāde virs 399 $. Jūsu kurss tiek fiksēts uz 30 minūtēm, tiklīdz atveras kase.Kurss fiksēts uz 30 minūtēm. Katra prece ir aizzīmogota, tās sērijas numurs ir pārbaudīts, un uz to attiecas 24 mēnešu garantija.Aizzīmogots, 24 mēnešu garantija.

Uzraudzītās preces Pieteikties
Green circuit board with black memory chips and gold contacts

A-Tech

A-Tech 4GB DDR3 1600 ECC UDIMM 1Rx8 Server Memory

SKU CH-ATAF-SW4HG

4GB DDR3 1600 ECC unbuffered UDIMM with CL11 latency for server upgrades

  • Capacity4GB
  • SpeedDDR3 1600 (PC3 12800)
  • CAS LatencyCL11
  • Voltage1.50V
  • ECCYes
  • Buffered/RegisteredUnbuffered
  • ECC protection safeguards data integrity with built-in error correction
  • DDR3 1600 speed delivers responsive server performance at PC3-12800 bandwidth
  • Single-rank 1Rx8 organisation optimises memory controller efficiency
  • Standard 1.50V operation matches DDR3 platform requirements
  • 240-pin UDIMM form factor fits compatible server and workstation slots

Compatible Replacement for Hynix HMT451E7BFR8C-PB

This A-Tech module is a 4GB DDR3 1600 ECC unbuffered DIMM built to replace the Hynix HMT451E7BFR8C-PB. It runs at PC3-12800 speed with CL11 latency at 1.50V and uses a 1Rx8 single-rank layout. The 240-pin form factor fits standard DDR3 server and workstation slots. Quality assurance testing and a lifetime warranty back the part.

Suits servers needing ECC UDIMM DDR3 1600

System builders maintaining DDR3 platforms that require error-correcting unbuffered memory at 1600 MHz will find this a direct fit. Buyers whose boards demand registered DIMMs, a different voltage, or higher density per slot cannot use this module. Compatibility must be verified against the system's qualified-vendor list before purchase.

Deciding spec: ECC unbuffered DDR3 1600 at 1.50V

The single specification that determines fit is the combination of ECC unbuffered operation, DDR3 1600 speed, and 1.50V voltage in a 240-pin DIMM. If the motherboard calls for registered ECC, a different voltage, or a non-ECC UDIMM, this module will not work. Match all three parameters to the system documentation.

Priekšrocības

  • ECC protection safeguards data integrity with built-in error correction
  • DDR3 1600 speed delivers responsive server performance at PC3-12800 bandwidth
  • Single-rank 1Rx8 organisation optimises memory controller efficiency
  • Standard 1.50V operation matches DDR3 platform requirements
  • 240-pin UDIMM form factor fits compatible server and workstation slots

Specifikācijas

BrandA-Tech
SeriesCompatible Replacement for Hynix
ModelHMT451E7BFR8C-PB
Capacity4GB
SpeedDDR3 1600 (PC3 12800)
CAS LatencyCL11
Voltage1.50V
ECCYes
Buffered/RegisteredUnbuffered
Rank1Rx8
ChipsetMajor Brand Chipset
FeaturesHMT451E7BFR8C-PB

Jautājumi par šo preci

How do I install this 240-pin DDR3 DIMM and what is the common mistake?

Align the notch on the module with the key in the slot, press down firmly until both side clips click shut; the common mistake is stopping when it feels seated but before the clips engage.

What maintenance or replacement will this 4GB ECC UDIMM need later?

No scheduled maintenance is required; replace the module only if memory diagnostics report correctable errors that become uncorrectable or if a system upgrade demands higher capacity.

What limit appears first on this CL11 1.5V module under sustained load?

The 1600 MT/s data rate and CL11 latency set the throughput ceiling; sustained workloads will saturate bandwidth before the 1.5V thermal envelope becomes a constraint.

Arī šajā sadaļā

Klienti arī salīdzināja

Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.