Mēs pieņemam kriptovalūtu — lai tā, kas Jums pieder, varētu nopirkt īstu aparatūru.Maksājiet kriptovalūtā, iztērējiet to īstai aparatūrai. Bezmaksas apdrošināta piegāde visā pasaulē virs 399 $. Vienkāršas, nemarķētas kastes, sūtītas no Vācijas.Bezmaksas apdrošināta piegāde virs 399 $. Jūsu kurss tiek fiksēts uz 30 minūtēm, tiklīdz atveras kase.Kurss fiksēts uz 30 minūtēm. Katra prece ir aizzīmogota, tās sērijas numurs ir pārbaudīts, un uz to attiecas 24 mēnešu garantija.Aizzīmogots, 24 mēnešu garantija.

Uzraudzītās preces Pieteikties
Alphacool 90-degree revolvable compression fitting in deep black finish

Alphacool

Alphacool 90° Revolvable Compression Fitting G1/4 10/16 Deep Black 17081

SKU CH-D9PH-ABDZE

A 90° revolvable compression fitting for 10/16 mm tubing with G1/4 thread in Deep Black finish

  • TypeFittings

Color Black

  • High flow inner diameter maximises coolant throughput
  • 90° revolvable design simplifies tight tubing routes
  • Deep Black chromatised finish resists peeling permanently
  • G1/4 thread fits standard water-cooling components
  • 10/16 mm compression suits 3/8" ID × 5/8" OD tubing

High-Flow 90° Revolvable Fitting

This G1/4 compression fitting accepts 10 mm inner and 16 mm outer diameter tubing for custom liquid-cooling loops. Its revolvable 90° design lets builders route tight corners without kinking the tube. The deep black chromatised finish bonds to the brass body for lasting colour. It suits enthusiasts who want clean angles and unrestricted flow in a single component.

Thermals Noise and Power

As a passive brass fitting it adds no heat, noise or electrical draw to the system. The enlarged inner bore reduces restriction so pumps run at lower speeds for the same flow rate. Leak-tight compression rings keep coolant contained during normal operation. No active cooling or power connection is required.

Build Quality and Daily Use

Chromatised surface treatment prevents peeling and maintains the deep black appearance over time. Knurled nuts allow hand-tight assembly without tools while sealing reliably. The revolvable elbow lets you orient the outlet after the base is threaded in. Buyers needing straight runs or different tube sizes will need other fittings.

Priekšrocības

  • High flow inner diameter maximises coolant throughput
  • 90° revolvable design simplifies tight tubing routes
  • Deep Black chromatised finish resists peeling permanently
  • G1/4 thread fits standard water-cooling components
  • 10/16 mm compression suits 3/8" ID × 5/8" OD tubing

Specifikācijas

TypeFittings

Citas šī modeļa versijas

Vēl 5 šajā sērijā

Viena saime, taču atšķirīga atmiņa, dzesētājs vai frekvence — salīdziniet, pirms izlemjat.

Jautājumi par šo preci

How do I install the G1/4 thread on the 90° revolvable fitting without cross-threading?

Screw the G1/4 male thread into the component by hand until the O-ring seats, then tighten a quarter-turn with a spanner; the revolvable elbow lets you orient the 10/16 compression end after the thread is secure.

What part will need replacement first on the Deep Black 17081 fitting?

The EPDM O-rings inside the compression nut and on the G1/4 thread will harden over time; replace them when you see weeping at the 10 mm ID / 16 mm OD tube joint.

What is the flow restriction limit of the 90° revolvable fitting under sustained pump pressure?

The tight 90° bend and 10 mm inner diameter create the first pressure-drop limit in a high-flow loop, so size your pump head to overcome that restriction.

Arī šajā sadaļā

Klienti arī salīdzināja

Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.