Mēs pieņemam kriptovalūtu — lai tā, kas Jums pieder, varētu nopirkt īstu aparatūru.Maksājiet kriptovalūtā, iztērējiet to īstai aparatūrai. Bezmaksas apdrošināta piegāde visā pasaulē virs 399 $. Vienkāršas, nemarķētas kastes, sūtītas no Vācijas.Bezmaksas apdrošināta piegāde virs 399 $. Jūsu kurss tiek fiksēts uz 30 minūtēm, tiklīdz atveras kase.Kurss fiksēts uz 30 minūtēm. Katra prece ir aizzīmogota, tās sērijas numurs ir pārbaudīts, un uz to attiecas 24 mēnešu garantija.Aizzīmogots, 24 mēnešu garantija.

Uzraudzītās preces Pieteikties
Matte-black brass compression fitting with G1/4 thread and hidden O-ring

Bitspower

Bitspower BP-MBCPF-CC6U G1/4" 7/16" ID 5/8" OD compression fitting

SKU CH-ZJFV-9NDBE MPN BP-MBCPF-CC6U

Connects 7/16" ID soft tubing to G1/4" ports with a matte-black brass compression fitting

  • TypeFittings
  • True Hi-Flow design maximises coolant throughput
  • G1/4" thread fits standard water-block ports
  • Hidden O-ring seals without visible rings
  • Hi-quality brass body resists corrosion
  • Matte black finish matches stealth builds

Straight G1/4" compression fitting

This Bitspower fitting connects soft tubing with a 7/16" inner diameter and 5/8" outer diameter to any component featuring a standard G1/4" thread. The matte black brass body uses a hidden O-ring design to maintain a clean appearance while sealing reliably under pressure. Its true hi-flow internal geometry minimises restriction for custom-loop builders.

Suits single-loop custom cooling

Enthusiasts assembling a custom water-cooling loop with matching soft-tubing dimensions will find the correct thread and seal here. The 5 mm thread length fits most water blocks, radiators, reservoirs and pumps without bottoming out. Builders using hard tubing, different inner-diameter sizes, or push-on barb connections cannot use this fitting.

G1/4" thread with 7/16" ID / 5/8" OD

The decisive specification is the combination of a G1/4" male thread and the precise 7/16" inner diameter paired with a 5/8" outer diameter for soft tubing. Only tubing manufactured to those exact dimensions will compress and seal correctly on this fitting. Verify your tubing measurements before ordering.

Priekšrocības

  • True Hi-Flow design maximises coolant throughput
  • G1/4" thread fits standard water-block ports
  • Hidden O-ring seals without visible rings
  • Hi-quality brass body resists corrosion
  • Matte black finish matches stealth builds

Specifikācijas

TypeFittings

Jautājumi par šo preci

How do I install this G1/4" compression fitting onto my water block without leaking?

Thread the fitting 5 mm into the G1/4" port by hand, then snug it with a wrench; push the 7/16" ID soft tubing fully over the barbs so the hidden O-ring seals, and tighten the compression collar evenly.

Which part of this fitting will need replacement first after long-term use?

The hidden O-ring inside the compression collar is the wear item; it can degrade from coolant additives or repeated disassembly, so keep spare O-rings for the 7/16" ID size.

What flow restriction appears first when running this fitting at high pump speeds?

The true Hi-Flow design minimises restriction, but the 7/16" inner diameter of the tubing remains the narrowest passage and sets the practical flow ceiling.

Arī šajā sadaļā

Klienti arī salīdzināja

Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.