Mēs pieņemam kriptovalūtu — lai tā, kas Jums pieder, varētu nopirkt īstu aparatūru.Maksājiet kriptovalūtā, iztērējiet to īstai aparatūrai. Bezmaksas apdrošināta piegāde visā pasaulē virs 399 $. Vienkāršas, nemarķētas kastes, sūtītas no Vācijas.Bezmaksas apdrošināta piegāde virs 399 $. Jūsu kurss tiek fiksēts uz 30 minūtēm, tiklīdz atveras kase.Kurss fiksēts uz 30 minūtēm. Katra prece ir aizzīmogota, tās sērijas numurs ir pārbaudīts, un uz to attiecas 24 mēnešu garantija.Aizzīmogots, 24 mēnešu garantija.

Uzraudzītās preces Pieteikties
Rectangular silver server power supply unit with rear vent grille and side handle

DELL

DELL 750W Redundant Power Supply for PowerEdge R730 server power supply

SKU CH-3NF5-YGGM9

750 W redundant power supply fits DELL PowerEdge R730 servers for continuous uptime

  • Weight5.0000LBS
  • 750 W output powers demanding PowerEdge R730 workloads
  • Redundant design keeps the server running if one unit fails
  • Hot-swap capability lets you replace the module without downtime
  • Compatible with Dell part numbers 57TFT, KNHJV and 1C8RF
  • 0000 lb weight fits standard 2U server bays

750W Redundant Power Supply for PowerEdge R730

This new 750-watt redundant power supply is built for the Dell PowerEdge R730 server. It serves administrators who need a direct replacement module to keep a dual-supply chassis running without downtime. The unit plugs into the server’s native power bay and shares load with a second supply for continuous operation. Buyers who need a non-redundant desktop PSU or a higher-wattage module for a different platform should look elsewhere.

750-watt output with redundant architecture

The single specification that decides fit is the 750W redundant design matched to the PowerEdge R730. The server’s power-distribution board expects this exact wattage and form factor, so any deviation will prevent the system from posting or balancing load correctly. No other capacity or connector layout is addressed by the supplied data.

Hot-plug installation into the server power bay

Installation is a hot-plug procedure: slide the module into the vacant bay until the latch clicks, and the server recognises it automatically. The most common issue is forgetting to seat the unit fully, which leaves the redundant pair unbalanced and triggers a firmware alert. A second frequent problem is mixing this 750W unit with a different-wattage supply, which the management controller will flag as a configuration error.

Priekšrocības

  • 750 W output powers demanding PowerEdge R730 workloads
  • Redundant design keeps the server running if one unit fails
  • Hot-swap capability lets you replace the module without downtime
  • Compatible with Dell part numbers 57TFT, KNHJV and 1C8RF
  • 0000 lb weight fits standard 2U server bays

Specifikācijas

BrandDELL
Weight5.0000LBS

Jautājumi par šo preci

How much usable power does the 750 W rating deliver inside a PowerEdge R730?

The unit supplies up to 750 W to the server, and the redundant design lets a second module take over instantly if one fails.

What connection standard does the 57TFT module use to slot into the R730 chassis?

It plugs directly into the PowerEdge R730 redundant power bay using the server's native hot-plug connector.

Will the 5.0000 lb unit fit the standard R730 mounting rails without adapters?

Yes, the supply matches the R730 form factor and locks into the existing chassis slots with no extra brackets.

Arī šajā sadaļā

Klienti arī salīdzināja

Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.