Mēs pieņemam kriptovalūtu — lai tā, kas Jums pieder, varētu nopirkt īstu aparatūru.Maksājiet kriptovalūtā, iztērējiet to īstai aparatūrai. Bezmaksas apdrošināta piegāde visā pasaulē virs 399 $. Vienkāršas, nemarķētas kastes, sūtītas no Vācijas.Bezmaksas apdrošināta piegāde virs 399 $. Jūsu kurss tiek fiksēts uz 30 minūtēm, tiklīdz atveras kase.Kurss fiksēts uz 30 minūtēm. Katra prece ir aizzīmogota, tās sērijas numurs ir pārbaudīts, un uz to attiecas 24 mēnešu garantija.Aizzīmogots, 24 mēnešu garantija.

Uzraudzītās preces Pieteikties
Rectangular silver server power supply unit with ventilation grille and power connectors visible

Lexindar

Lexindar APW12 4000W server power supply

SKU CH-PVP9-3TZXV MPN APW12

A 4000W server power supply with active PFC built for S19 mining machines

  • Maximum Powerbuffer_48114
  • 4000W capacity powers demanding mining rigs
  • Active PFC improves input current quality
  • 48114 W buffer handles peak load spikes
  • 255×255×70 mm footprint fits dense server racks
  • New Lexindar unit built for S19 series machines

Designed for S19 mining rigs

The Lexindar APW12 delivers 4000W of continuous power to S19 full series mining machines. Its active PFC topology corrects the input current waveform for stable operation on industrial circuits. The unit omits modular cabling and multi‑12V support, so every connection is fixed at the factory. Builders who need redundant or hot‑swap supplies cannot use this model.

Upgrade from lower‑wattage server units

When an existing supply cannot sustain the S19 peak draw, the APW12 replaces it with a single 4000W source. The jump is worth it only if the rack circuit and cooling can absorb the higher thermal load. No 80 PLUS licence is held, so efficiency claims rest on the manufacturer’s internal data alone. Operators who require certified efficiency ratings must look elsewhere.

Sustained output under buffer_48114

The supply is rated to maintain full output while the buffer_48114 condition persists, rather than only in short bursts. Active PFC helps keep voltage steady as line conditions vary across shifts. Gross weight reaches 4kg and the enclosure measures 255 by 255 by 70mm, so rack density planning must account for the fixed form factor. Environments that demand modular cable routing or redundant hot‑swap bays fall outside the intended use case.

Priekšrocības

  • 4000W capacity powers demanding mining rigs
  • Active PFC improves input current quality
  • 48114 W buffer handles peak load spikes
  • 255×255×70 mm footprint fits dense server racks
  • New Lexindar unit built for S19 series machines

Specifikācijas

Seriesserver power
Maximum Powerbuffer_48114

Jautājumi par šo preci

What are the exact case dimensions this 255 mm × 255 mm × 70 mm unit requires to fit?

The power supply occupies a 255 mm by 255 mm footprint and stands 70 mm tall, so the chassis must clear at least those three measurements in each axis.

Which installation step do builders most often skip when fitting this active-PFC, non-modular supply into an S19-series miner?

They forget to seat every fixed cable bundle into the miner’s hash-board connectors before torquing the four mounting screws, leaving loose pins that cause intermittent power.

When should the internal cooling fan be inspected or replaced on this 4 kg, 4000 W server supply running continuous mining loads?

Plan a visual and acoustic check every six months; replace the fan once bearing noise appears or airflow drops, typically after two to three years of 24/7 operation.

Arī šajā sadaļā

Klienti arī salīdzināja

Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.