BFKK
BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
214,99 $
0.0027736BTC
Krājumā
NEMIX RAM
NEMIX RAM 576GB 12x48GB DDR5 5600 CL46 2Rx8 1.1V 288-pin ECC RDIMM for Supermicro H13SSH-E
576 GB DDR5 5600 registered ECC kit with twelve 48 GB modules at CL46 and 1.1 V for Supermicro H13SSH-E
- Capacity576GB (12 x 48GB)
- Type288-Pin DDR5 RDIMM
- SpeedDDR5 5600 (PC5 44800)
- CAS LatencyCL46
- Voltage1.10V
- ECCYes
- 576 GB total capacity from twelve 48 GB modules for maximum server density
- DDR5 5600 MT/s rated speed matches the platform controller for full throughput
- CL46 CAS latency at 1.1 V delivers specified timing without over-voltage
- Registered ECC 2Rx8 architecture offloads the controller and corrects single-bit errors
- 288-pin RDIMM form factor verified for Supermicro H13SSH-E motherboard fitment
576GB DDR5 5600 ECC RDIMM Kit
This NEMIX RAM kit delivers 576GB of DDR5 5600 memory across twelve 48GB registered DIMMs. Each module runs at 1.1V with CL46 latency and a 2Rx8 organization. The registered ECC design is built for the Supermicro H13SSH-E motherboard and its memory controller requirements.
Suited for max-capacity server builds.
The kit targets administrators who must fully populate the H13SSH-E with registered ECC modules at the board's rated speed. It is not for desktop PCs, workstations that accept only unbuffered DIMMs, or any system that cannot use 288-pin DDR5 RDIMMs.
Straightforward slot installation.
Modules install like any 288-pin DDR5 RDIMM by aligning the key notch and pressing until the latches engage. The main risk is ignoring the motherboard manual's population sequence, which can prevent the system from recognizing the full 576GB or running at DDR5 5600.
Priekšrocības
- 576 GB total capacity from twelve 48 GB modules for maximum server density
- DDR5 5600 MT/s rated speed matches the platform controller for full throughput
- CL46 CAS latency at 1.1 V delivers specified timing without over-voltage
- Registered ECC 2Rx8 architecture offloads the controller and corrects single-bit errors
- 288-pin RDIMM form factor verified for Supermicro H13SSH-E motherboard fitment
Specifikācijas
| Brand | NEMIX RAM |
|---|---|
| Series | NEMIX RAM Original Series Server Memory |
| Model | DDR5 ECC RDIMM Registered Server Memory |
| Part Number | MR44800-4828K12 |
| Capacity | 576GB (12 x 48GB) |
| Type | 288-Pin DDR5 RDIMM |
| Speed | DDR5 5600 (PC5 44800) |
| CAS Latency | CL46 |
| Voltage | 1.10V |
| ECC | Yes |
| Buffered/Registered | Registered |
| Rank | 2Rx8 |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Heat Spreader | No |
| Compatible System | Supermicro |
| Features | DDR5 ECC RDIMM Motherboard Compatible |
| Package Content | 576GB 12X48GB DDR5 5600MHz PC5-44800 2Rx8 1.1V 288-PIN ECC RDIMM KIT |
Jautājumi par šo preci
Does the Supermicro H13SSH-E motherboard need all 12 slots filled for this 576GB kit to operate?
The kit contains 12 modules of 48GB each. The motherboard's manual defines the supported population rules and any minimum-slot requirements for full-capacity operation.
Will these registered ECC DDR5 modules work in a board that currently runs unbuffered non-ECC DDR5 DIMMs?
No. This kit uses 288-pin registered RDIMMs with ECC. A motherboard designed for unbuffered UDIMMs cannot accept registered modules, and mixing the two types is not supported.
How can I confirm the kit is running at DDR5-5600 with CL46 timings after installation?
Enter the system BIOS or use an OS-level tool such as dmidecode to verify the reported speed of 5600 MT/s, CAS latency of 46, voltage of 1.10V and that all 576GB are detected.
Arī šajā sadaļā
Klienti arī salīdzināja
Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.
