BFKK
BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
214,99 $
0.00278452BTC
Krājumā
NEMIX RAM
NEMIX RAM 64GB (4x16GB) DDR5 5600 CL46 288-Pin UDIMM Supermicro BH4SRG memory upgrade
A 64 GB kit of four 16 GB DDR5 5600 CL46 288-pin UDIMM modules at 1.1 V, validated for Supermicro BH4SRG motherboards
- Capacity64GB (4 x 16GB)
- SpeedDDR5 5600 (PC5 44800)
- ECCNo
- Buffered/RegisteredUnbuffered
- ChipsetMajor OEM Samsung, Micron, Hynix
- Voltage1.10V
- 64 GB total capacity across four 16 GB modules
- DDR5 5600 MT/s speed rated at PC5-44800 bandwidth
- CL46 CAS latency with 1.1 V operating voltage
- 288-pin unbuffered non-ECC UDIMM form factor
- Built with major OEM Samsung, Micron or Hynix chips
Capacity and compatibility
This kit provides 64GB of DDR5 memory across four 16GB modules. It is built for the Supermicro BH4SRG motherboard and follows the 288-pin UDIMM form factor. The non-ECC unbuffered design suits desktop and workstation platforms that do not require error correction.
Sustained-load behaviour
Operating at 1.1V with CL46 latency, the modules maintain the DDR5 5600 data rate during extended workloads. The 1Rx8 organisation keeps signal loading low on each channel. Major OEM DRAM from Samsung, Micron or Hynix supplies consistent timing under continuous read and write cycles.
DDR5 interface limits
The PC5-44800 rating sets the peak transfer ceiling for this standard. Bandwidth cannot exceed the DDR5 5600 specification regardless of motherboard capabilities. Systems that only support lower DDR5 speeds will run the kit at the highest mutually supported frequency.
Priekšrocības
- 64 GB total capacity across four 16 GB modules
- DDR5 5600 MT/s speed rated at PC5-44800 bandwidth
- CL46 CAS latency with 1.1 V operating voltage
- 288-pin unbuffered non-ECC UDIMM form factor
- Built with major OEM Samsung, Micron or Hynix chips
Specifikācijas
| Brand | NEMIX RAM |
|---|---|
| Series | NEMIX RAM Original Series Memory |
| Model | DDR5 Non-ECC Unbuffered UDIMM Memory |
| Part Number | MD44800-618K4 |
| Capacity | 64GB (4 x 16GB) |
| Speed | DDR5 5600 (PC5 44800) |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Voltage | 1.10V |
| Compatible System | Supermicro |
| CAS Latency | CL46 |
| Heat Spreader | No |
| Type | 288-Pin DDR5 UDIMM |
| Rank | 1Rx8 |
| Features | DDR5 Non-ECC Unbuffered UDIMM Motherboard Compatible |
| Package Content | 64GB (4 x 16GB) DDR5 5600MHz PC5-44800 1Rx8 1.1V 288-PIN Non-ECC UDIMM KIT |
Jautājumi par šo preci
Will the 1.1 V DDR5 modules stay cool and quiet during all-day operation?
The kit runs at the standard 1.1 V DDR5 voltage with no heat spreader, so it relies on case airflow; power draw is typical for 5600 MT/s unbuffered UDIMMs.
What motherboard slot and CPU memory controller do I need for this 4×16 GB kit to work?
You need a Supermicro BH4SRG motherboard with four 288-pin DDR5 UDIMM slots and a CPU that supports DDR5-5600 non-ECC unbuffered memory.
Can I mix this CL46 DDR5-5600 kit with slower DDR5 modules already installed in the same board?
Mixing speeds or latencies forces all modules to run at the lowest common speed and highest latency; for best stability use four identical 16 GB 1Rx8 CL46 modules.
Arī šajā sadaļā
Klienti arī salīdzināja
Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.
