Mēs pieņemam kriptovalūtu — lai tā, kas Jums pieder, varētu nopirkt īstu aparatūru.Maksājiet kriptovalūtā, iztērējiet to īstai aparatūrai. Bezmaksas apdrošināta piegāde visā pasaulē virs 399 $. Vienkāršas, nemarķētas kastes, sūtītas no Vācijas.Bezmaksas apdrošināta piegāde virs 399 $. Jūsu kurss tiek fiksēts uz 30 minūtēm, tiklīdz atveras kase.Kurss fiksēts uz 30 minūtēm. Katra prece ir aizzīmogota, tās sērijas numurs ir pārbaudīts, un uz to attiecas 24 mēnešu garantija.Aizzīmogots, 24 mēnešu garantija.

Uzraudzītās preces Pieteikties
Green circuit board with black memory chips and gold edge connectors

OWC

OWC 4GB DDR4 2133MHz PC4-17000 CL15 1.2V 288pin Non-ECC UDIMM memory upgrade

SKU CH-2RZQ-ZNKP3

Adds 4GB of DDR4 2133MHz memory to HP ProDesk 600 G3 SFF and Tower systems

  • Capacity4GB
  • Type288-Pin DDR4 Non-ECC UDIMM
  • SpeedDDR4 2133 (PC4 17000)
  • CAS LatencyCL15
  • Voltage1.2V
  • ECCNo
  • Boosts responsiveness with a 2133 MHz DDR4 upgrade
  • Fits HP ProDesk 600 G3 SFF and Tower systems
  • Runs at 1.2 V for lower power draw
  • Meets JEDEC and RoHS standards for safe installation
  • Single-rank 1Rx8 layout for broad motherboard compatibility

OWC 4GB DDR4 module for HP ProDesk 600 G3

This 4GB DDR4 UDIMM is built for HP ProDesk 600 G3 SFF and Tower systems. It targets owners of those desktops who need a straightforward capacity increase. The module is unbuffered, non-ECC and runs at the standard 1.2V.

DDR4 2133 CL15 operates at JEDEC base speed

The PC4-17000 rating means the memory runs at 2133 MT/s with CL15 latency. That is the baseline DDR4 data rate, so bandwidth is limited to what the platform's memory controller defines for this speed grade. No higher JEDEC profiles are supported by this module.

Replaces or adds to original factory DIMMs

Use it to replace a smaller factory stick or to fill an empty slot when the board has free sockets. The upgrade is worthwhile when the system currently runs with less than the desired total capacity and the workload benefits from more RAM rather than faster RAM. Buyers who need ECC, registered modules or speeds above 2133 MT/s cannot use this part.

Priekšrocības

  • Boosts responsiveness with a 2133 MHz DDR4 upgrade
  • Fits HP ProDesk 600 G3 SFF and Tower systems
  • Runs at 1.2 V for lower power draw
  • Meets JEDEC and RoHS standards for safe installation
  • Single-rank 1Rx8 layout for broad motherboard compatibility

Specifikācijas

BrandOWC
Part Number2U1D41R804GB
Capacity4GB
Type288-Pin DDR4 Non-ECC UDIMM
SpeedDDR4 2133 (PC4 17000)
CAS LatencyCL15
Voltage1.2V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
Heat SpreaderNo
Compatible SystemHP ProDesk 600 G3 SFF
HP ProDesk 600 G3 Tower

Citas šī modeļa versijas

Vēl 5 šajā sērijā

Viena saime, taču atšķirīga atmiņa, dzesētājs vai frekvence — salīdziniet, pirms izlemjat.

Jautājumi par šo preci

Is the 4GB module the only capacity offered for this HP ProDesk 600 G3 upgrade?

Yes, this listing is for a single 4GB DDR4 2133MHz UDIMM. The part number 2U1D41R804GB identifies this specific capacity.

What real-world speed will I see from the PC4-17000 rating once installed?

The module runs at 2133MHz with CL15 latency at 1.2V, delivering the standard JEDEC DDR4-2133 data rate in your HP ProDesk 600 G3.

Does the 288-pin DDR4 interface limit the bandwidth on my HP ProDesk 600 G3 SFF?

The 288-pin unbuffered DIMM fits the standard DDR4 slots on the 600 G3 SFF and Tower, operating at the platform-supported 2133MHz speed.

Arī šajā sadaļā

Klienti arī salīdzināja

Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.