Mēs pieņemam kriptovalūtu — lai tā, kas Jums pieder, varētu nopirkt īstu aparatūru.Maksājiet kriptovalūtā, iztērējiet to īstai aparatūrai. Bezmaksas apdrošināta piegāde visā pasaulē virs 399 $. Vienkāršas, nemarķētas kastes, sūtītas no Vācijas.Bezmaksas apdrošināta piegāde virs 399 $. Jūsu kurss tiek fiksēts uz 30 minūtēm, tiklīdz atveras kase.Kurss fiksēts uz 30 minūtēm. Katra prece ir aizzīmogota, tās sērijas numurs ir pārbaudīts, un uz to attiecas 24 mēnešu garantija.Aizzīmogots, 24 mēnešu garantija.

Uzraudzītās preces Pieteikties
Green circuit board with black memory chips and gold edge connectors

OWC

OWC 8GB DDR4 2666MHz CL19 1.2V 288-Pin UDIMM for HP OMEN X 900-210/211/212/213/250

SKU CH-8RH8-VQXWS

An 8 GB DDR4 UDIMM running at 2666 MHz CL19, validated for HP OMEN X 900-210, 900-211, 900-212, 900-213 and 900-250 desktops

  • Capacity8GB
  • Type288-Pin DDR4 Non-ECC UDIMM
  • SpeedDDR4 2666 (PC4 21300)
  • CAS LatencyCL19
  • Voltage1.2V
  • ECCNo
  • Designed for HP OMEN X 900-210, 211, 212, 213 and 250 desktops
  • JEDEC compliant DDR4 2666MHz CL19 at 1.2V for stable operation
  • 8GB unbuffered non-ECC UDIMM adds responsive multitasking capacity
  • 288-pin form factor fits standard desktop DIMM slots directly
  • Backward compatible with 2133MHz and 2400MHz systems automatically

OWC 8GB DDR4 2666MHz UDIMM

This OWC module provides 8GB of DDR4 memory at 2666MHz with CL19 latency and 1.2V operation. It is built as a 288-pin non-ECC unbuffered UDIMM specifically validated for HP OMEN X 900-210, 900-211, 900-212, 900-213 and 900-250 desktops. The part number is 2U6D41R808GB.

Upgrading from lower capacity or slower DDR4

The jump is worth it when the system ships with less than 8GB per slot or runs at 2133MHz or 2400MHz. This module is backward compatible with those speeds and will run at the highest rate the platform supports. Buyers who need ECC error correction or registered buffering cannot use this UDIMM.

Tool-free slot installation

The UDIMM inserts vertically into the motherboard DIMM slots; no screws or cables are required. Most cases allow access by removing a side panel. The common mistake is not seating the module fully until the retention clips click, which causes a no-post condition. Another issue is mixing modules with different ranks or voltages, which can prevent the system from training memory correctly.

Priekšrocības

  • Designed for HP OMEN X 900-210, 211, 212, 213 and 250 desktops
  • JEDEC compliant DDR4 2666MHz CL19 at 1.2V for stable operation
  • 8GB unbuffered non-ECC UDIMM adds responsive multitasking capacity
  • 288-pin form factor fits standard desktop DIMM slots directly
  • Backward compatible with 2133MHz and 2400MHz systems automatically

Specifikācijas

BrandOWC
Part Number2U6D41R808GB
Capacity8GB
Type288-Pin DDR4 Non-ECC UDIMM
SpeedDDR4 2666 (PC4 21300)
CAS LatencyCL19
Voltage1.2V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
Heat SpreaderNo
Compatible SystemHP OMEN X 900-210no
HP OMEN X 900-211no
HP OMEN X 900-212no
HP OMEN X 900-213no
HP OMEN X 900-250

Citas šī modeļa versijas

Vēl 5 šajā sērijā

Viena saime, taču atšķirīga atmiņa, dzesētājs vai frekvence — salīdziniet, pirms izlemjat.

Jautājumi par šo preci

Will the 288-pin DDR4 UDIMM fit the HP OMEN X 900-210, 900-211, 900-212, 900-213 or 900-250 motherboard slots?

Yes, the 288-pin DDR4 UDIMM is built to the JEDEC standard for those HP OMEN X models and installs in the standard desktop DIMM slots.

What is the correct way to seat the 1Rx8 module so the retention clips lock on both ends?

Align the notch with the slot key, press straight down with even pressure until both side clips snap closed, and verify the module sits flat without tilting.

Does the CL19 1.2V module need any firmware update or heat-spreader replacement over time?

No firmware update is required; the module has no heat spreader and is designed to run within JEDEC limits for the life of the system.

Arī šajā sadaļā

Klienti arī salīdzināja

Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.