HP 507283-001 146GB 10000 RPM SAS 2.5" internal hard drive
- Bare Drive
- SATA
Mēs pieņemam kriptovalūtu — lai tā, kas Jums pieder, varētu nopirkt īstu aparatūru.Maksājiet kriptovalūtā, iztērējiet to īstai aparatūrai. Bezmaksas apdrošināta piegāde visā pasaulē virs 399 $. Vienkāršas, nemarķētas kastes, sūtītas no Vācijas.Bezmaksas apdrošināta piegāde virs 399 $. Jūsu kurss tiek fiksēts uz 30 minūtēm, tiklīdz atveras kase.Kurss fiksēts uz 30 minūtēm. Katra prece ir aizzīmogota, tās sērijas numurs ir pārbaudīts, un uz to attiecas 24 mēnešu garantija.Aizzīmogots, 24 mēnešu garantija.
SAMSUNG
PCIe 4.0 x4 M.2 2280 SSD with 4 TB capacity, NVMe 2.0, sequential reads up to 7450 MBps and writes up to 6900 MBps
The Samsung 990 PRO w/ Heatsink Gaming Package is an M.2 2280 internal SSD built for consumers who need large, fast storage. It uses V7 V-NAND 3bit MLC memory and a Samsung controller on a PCI-Express Gen 4.0 x4 interface with NVMe 2.0. The 4TB capacity suits modern game libraries and heavy workloads.
Sequential reads reach up to 7450 MBps and writes up to 6900 MBps, giving wide headroom for loading large assets and sustained transfers. The bundled heatsink helps maintain those speeds under prolonged loads, though the drive will still throttle once its thermal ceiling is reached.
The included heatsink attaches directly to the drive to dissipate heat during extended gaming or creative sessions. It changes the thermal profile so the controller can hold peak throughput longer than a bare module would. No extra software or accessories are mentioned in the supplied data.
| Brand | SAMSUNG |
|---|---|
| Series | 990 PRO w/ Heatsink Gaming Package |
| Model | MZ-V9P4T0GW |
| Part Number | MZ-V9P4T0GW |
| Device Type | Internal Solid State Drive (SSD) |
| Used For | Consumer |
| Form Factor | M.2 2280 |
| Capacity | 4TB |
| Memory Components | V7 V-NAND 3bit MLC |
| Interface | PCI-Express Gen 4.0 x4, NVMe 2.0 |
| Controller | Samsung |
| Max Sequential Read | Up to 7450 MBps |
| Max Sequential Write | Up to 6900 MBps |
The drive uses a PCI-Express Gen 4.0 x4 interface, so it will operate at Gen 3.0 speeds when installed in a Gen 3.0 slot. The M.2 2280 form factor is unchanged, so it physically fits the same slot.
Run a benchmark such as CrystalDiskMark and compare the results to the specified maximums of 7450 MBps read and 6900 MBps write. Ensure the motherboard BIOS is set to PCIe Gen 4.0 and NVMe 2.0 is enabled for the slot.
The heatsink is pre-attached to the M.2 2280 module. A mounting screw is typically provided by the motherboard manufacturer, not the drive package, so check your board's accessory kit before installation.
Arī šajā sadaļā
Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.
Kriptovalūta, kurā maksājat, un valūta, kurā redzat cenas.
Nosūtīts no Jūsu maciņa, noformējot pasūtījumu
Tikai informatīvi — katalogā cenas norādītas ASV dolāros
Neviena valūta neatbilst.
Izvēlieties valodu, kurā vietne sarunājas ar Jums.
Pirmo reizi šeit?
Jau ir konts?
Automātiskas atiestatīšanas nav: šis veikals nesūta e-pastus, tāpēc nav arī vienreizējas saites, ko pieprasīt. Atstājiet adresi kontā, un tā tiks apstrādāta manuāli.
Pieprasījums saņemts
Uz Jūsu e-pastu nekas neatnāks — šis veikals vispār nesūta e-pastus. Kāds šos pieprasījumus apstrādā manuāli.
Atcerējāties?