Kripto para kabul ediyoruz — böylece elinizdeki koinlerle gerçek donanım alabilirsiniz.Kripto parayla ödeyin, onu gerçek donanıma harcayın. $399 üzeri siparişlerde dünya genelinde sigortalı kargo ücretsizdir. Sade, markasız koliler Almanya’dan gönderilir.$399 üzeri siparişlerde sigortalı kargo ücretsizdir. Ödeme sayfası açıldığında kurunuz 30 dakika kilitli kalır.Kur 30 dakika kilitli. Her ürün mühürlüdür, seri numarası kontrol edilir ve 24 ay garanti kapsamındadır.Mühürlü, 24 ay garantili.

Favori ürünler Giriş yap
Green printed circuit board with black memory chips in a 288-pin DDR4 UDIMM stick

OWC

OWC 16GB DDR4 2133MHz CL15 1.2V 288pin UDIMM memory upgrade

SKU CH-YK8W-J8W1N

A 16 GB DDR4 module running at 2133 MHz with CL15 latency, validated for HP ENVY Phoenix 860‑005nf, 860‑007na, 860‑008na, 860‑008nf and 860‑009na desktops

  • Capacity16GB
  • Type288-Pin DDR4 Non-ECC UDIMM
  • SpeedDDR4 2133 (PC4 17000)
  • CAS LatencyCL15
  • Voltage1.2V
  • ECCNo
  • 16 GB capacity adds headroom for multitasking
  • DDR4 2133 MHz CL15 speed matches system requirements
  • 2 V low voltage reduces power draw
  • 288-pin UDIMM form factor fits HP Envy Phoenix 860 series
  • JEDEC and RoHS compliant for warranty-safe upgrade

HP ENVY Phoenix compatible DDR4

This 16GB DDR4 2133MHz CL15 module is built for HP ENVY Phoenix desktops including the 860-005nf, 860-007na, 860-008na, 860-008nf and 860-009na. It runs at 1.2V as an unbuffered non-ECC UDIMM. The 2Rx8 rank configuration matches the platform requirements. Owners of these specific models can add capacity without compatibility guesswork.

Upgrading from lower capacity DDR4

Systems shipping with 8GB or a single 16GB stick benefit most from this addition. The jump is worth it when multitasking slows down or larger files exceed available memory. It will not help if the board already holds the maximum supported modules or if the bottleneck lies elsewhere. Buyers needing ECC or registered memory cannot use this module.

Tool-free DIMM installation

Installation requires opening the case and pressing the module into a free 288-pin slot until the retention clips click. The usual problem is seating the stick unevenly so the system fails to POST. Another common issue is mixing speeds which forces all modules to run at the slowest rate. No heat spreader means clearance is rarely a concern.

Öne çıkanlar

  • 16 GB capacity adds headroom for multitasking
  • DDR4 2133 MHz CL15 speed matches system requirements
  • 2 V low voltage reduces power draw
  • 288-pin UDIMM form factor fits HP Envy Phoenix 860 series
  • JEDEC and RoHS compliant for warranty-safe upgrade

Teknik özellikler

BrandOWC
Part Number2U1D42R816GB
Capacity16GB
Type288-Pin DDR4 Non-ECC UDIMM
SpeedDDR4 2133 (PC4 17000)
CAS LatencyCL15
Voltage1.2V
ECCNo
Buffered/RegisteredUnbuffered
Rank2Rx8
Heat SpreaderNo
Compatible SystemHP ENVY Phoenix 860-005nf
HP ENVY Phoenix 860-007na
HP ENVY Phoenix 860-008na
HP ENVY Phoenix 860-008nf
HP ENVY Phoenix 860-009na

Bu modelin diğer sürümleri

Aynı seriden 5 tane daha

Aynı aile, farklı bellek, soğutucu veya frekans — karar vermeden önce karşılaştırın.

Bu ürünle ilgili sorular

Will the 288-pin DDR4 UDIMM fit the HP ENVY Phoenix 860-005nf memory slots?

Yes, the module is a 288-pin DDR4 UDIMM built to JEDEC spec and tested for the listed HP ENVY Phoenix 860 models including the 860-005nf.

What is the correct way to seat the module, and what step do people often miss?

Align the notch with the slot key, press straight down until both retention clips click, then verify the clips are fully locked — the missed step is not checking both clips.

Does the 16 GB 2Rx8 module need any firmware updates or periodic replacement?

No firmware is required; the memory is a passive component with no moving parts and is covered by a limited lifetime warranty, so no scheduled replacement is needed.

Bu reyondan diğerleri

Müşteriler bunları karşılaştırdı

Aynı raf, aynı sipariş tamamlama — sekiz koin ve 30 dakikalık kur kilidi.