Δεχόμαστε κρυπτονομίσματα — έτσι ώστε αυτά που κατέχετε να μπορούν να αγοράσουν πραγματικό εξοπλισμό.Πληρώστε σε κρυπτονομίσματα, ξοδέψτε τα σε πραγματικό εξοπλισμό. Δωρεάν ασφαλισμένη αποστολή παγκοσμίως άνω των 399 $. Ουδέτερες κούτες αποστολής, χωρίς σήμανση, από τη Γερμανία.Δωρεάν ασφαλισμένη αποστολή άνω των 399 $. Η ισοτιμία σας κλειδώνει για 30 λεπτά μόλις ανοίξει το ταμείο.Κλείδωμα ισοτιμίας 30 λεπτών. Κάθε προϊόν είναι σφραγισμένο, ελεγμένο ως προς τον σειριακό αριθμό του, και καλύπτεται από εγγύηση 24 μηνών.Σφραγισμένο, με εγγύηση 24 μηνών.

Παρακολουθούμενα είδη Σύνδεση
Four white brass compression fittings for 14 mm rigid tubing

Bitspower

Bitspower BP-DWEMLA14-4P 14 mm liquid cooler fitting 4-pack

SKU CH-MA27-KYMM7 MPN BP-DWEMLA14-4P

Four G1/4" multi-link compression fittings for 14 mm OD rigid tubing, machined from brass with a Deluxe White finish

  • TypeFittings
  • Multi-link design enables complex hard-tube routing
  • Premium brass construction ensures durable leak-free seals
  • G1/4" thread fits standard water-cooling components
  • Four fittings in one pack covers full loop
  • Optimised for 14 mm OD rigid tubing

G1/4" Multi-Link Fittings for 14mm Hard Tubing

This four-pack of Bitspower compression fittings is built for custom liquid-cooling loops that use 14mm outer-diameter rigid tubing. The G1/4" thread matches standard water-block, radiator and reservoir ports, while the multi-link design allows extended routing runs without extra adapters. Deluxe White plating gives a consistent finish across visible loop sections. RoHS compliance confirms the brass construction meets restricted-substance limits.

Installing the compression rings onto rigid tubing

Slide the compression nut and split ring onto the cut tube, then press the tube firmly into the fitting body until it bottoms out before tightening the nut by hand plus a quarter turn with a wrench. A clean, square cut on the 14mm tubing is critical; burrs or an angled cut prevent a full seal and cause leaks under pressure. Over-tightening can deform the brass threads or crack the tubing, so stop when resistance increases sharply. Pressure-test the loop with the system powered off before final assembly.

Verify thread compatibility and tubing dimensions

Confirm every component in your loop uses G1/4" female threads, as other thread standards will not seal correctly. Measure your rigid tubing to ensure a true 14mm outer diameter; undersized or oversized tube will not compress the split ring evenly. Plan the routing so each multi-link segment has enough straight length for the compression nuts to engage fully without bending stress. Ensure your loop design includes a drain port and fill point accessible after these fittings are installed.

Βασικά χαρακτηριστικά

  • Multi-link design enables complex hard-tube routing
  • Premium brass construction ensures durable leak-free seals
  • G1/4" thread fits standard water-cooling components
  • Four fittings in one pack covers full loop
  • Optimised for 14 mm OD rigid tubing

Προδιαγραφές

TypeFittings

Ερωτήσεις για αυτό το προϊόν

How can I confirm the G1/4" multi-link fittings are seated correctly after installing them on 14mm OD hard tubing?

When assembled correctly the compression fittings are simple to use and extremely secure; verify each fitting is fully tightened and check for leaks during the initial loop test.

What comes in the 4-pack and is any additional hardware required for a multi-link extension run?

The pack contains four Deluxe White G1/4" multi-link compression fittings made of hi-quality brass for 14mm OD rigid tubing; no extra components are included.

Which version of the Bitspower multi-link fitting should I choose for a 14mm OD hard-tube loop?

Model BP-DWEMLA14-4P is designed specifically for 14mm OD rigid tubing with G1/4" threads and is supplied as a four-piece value pack in Deluxe White.

Επίσης σε αυτό το ράφι

Οι πελάτες σύγκριναν και αυτά

Ίδιο ράφι, ίδιο ταμείο — οκτώ νομίσματα και κλείδωμα ισοτιμίας 30 λεπτών.