Δεχόμαστε κρυπτονομίσματα — έτσι ώστε αυτά που κατέχετε να μπορούν να αγοράσουν πραγματικό εξοπλισμό.Πληρώστε σε κρυπτονομίσματα, ξοδέψτε τα σε πραγματικό εξοπλισμό. Δωρεάν ασφαλισμένη αποστολή παγκοσμίως άνω των 399 $. Ουδέτερες κούτες αποστολής, χωρίς σήμανση, από τη Γερμανία.Δωρεάν ασφαλισμένη αποστολή άνω των 399 $. Η ισοτιμία σας κλειδώνει για 30 λεπτά μόλις ανοίξει το ταμείο.Κλείδωμα ισοτιμίας 30 λεπτών. Κάθε προϊόν είναι σφραγισμένο, ελεγμένο ως προς τον σειριακό αριθμό του, και καλύπτεται από εγγύηση 24 μηνών.Σφραγισμένο, με εγγύηση 24 μηνών.

Παρακολουθούμενα είδη Σύνδεση
Four silver G1/4 inch compression fittings for 16mm rigid tubing

Bitspower

Bitspower BP-EMLA16-4P G1/4" Multi-Link Fitting 16mm OD 4-pack

SKU CH-V1DQ-M9VY4 MPN BP-EMLA16-4P

G1/4" multi-link compression fittings for 16mm OD rigid tubing, supplied as a four-piece brass pack

  • TypeFittings
  • Multi-link design enables secure hard-tube extensions
  • High-quality brass construction ensures durable leak-free seals
  • G1/4" threads fit standard water-cooling components
  • Four Silver Shining fittings included for multi-point builds
  • RoHS compliant materials meet environmental safety standards

Multi-Link Fitting 4-Pack

This four-piece set provides G1/4" compression fittings built for 16mm OD rigid tubing in custom water-cooling loops. The brass construction and silver finish suit builders who want a clean, uniform look across multiple connection points. Each fitting is designed to join hard-tube runs securely while maintaining a consistent aesthetic.

Brass Construction and Multi-Link Design

The high-quality brass body resists corrosion and provides a solid sealing surface for compression rings. Multi-link geometry allows several fittings to be chained together, letting you extend or redirect tubing runs without extra adapters. The silver shining coating matches other Bitspower components for a cohesive appearance.

Installation Notes

Slide the compression ring and nut onto the tube, insert the tube fully into the fitting body, then tighten the nut by hand before a final quarter-turn with a wrench. The most common issue is an uneven tube cut that prevents a full seat, causing a slow leak when the loop is pressurised. Deburring the inside and outside edges of every 16mm cut eliminates this problem.

Βασικά χαρακτηριστικά

  • Multi-link design enables secure hard-tube extensions
  • High-quality brass construction ensures durable leak-free seals
  • G1/4" threads fit standard water-cooling components
  • Four Silver Shining fittings included for multi-point builds
  • RoHS compliant materials meet environmental safety standards

Προδιαγραφές

TypeFittings

Ερωτήσεις για αυτό το προϊόν

Will the G1/4" threads on these multi-link fittings need periodic re-tightening or O-ring replacement over time?

The brass compression design seals against 16mm OD hard tubing with captive O-rings; inspect seals during loop maintenance and replace only if leakage appears.

What is the practical bending-radius limit when routing 16mm rigid tube between these fittings in a tight loop?

Each fitting adds roughly 16 mm of straight engagement, so allow at least that much straight run before the first bend to avoid stress on the compression seal.

Do the brass bodies and silver finish add noticeable heat or restrict flow when the loop runs continuously?

Brass conducts heat neutrally and the full-bore G1/4" channel adds negligible restriction; the fittings remain at coolant temperature with no audible noise.

Επίσης σε αυτό το ράφι

Οι πελάτες σύγκριναν και αυτά

Ίδιο ράφι, ίδιο ταμείο — οκτώ νομίσματα και κλείδωμα ισοτιμίας 30 λεπτών.