Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Four silver G1/4 inch compression fittings for 16mm rigid tubing

Bitspower

Bitspower BP-EMLA16-4P G1/4" Multi-Link Fitting 16mm OD 4-pack

SKU CH-V1DQ-M9VY4 MPN BP-EMLA16-4P

G1/4" multi-link compression fittings for 16mm OD rigid tubing, supplied as a four-piece brass pack

  • TypeFittings
  • Multi-link design enables secure hard-tube extensions
  • High-quality brass construction ensures durable leak-free seals
  • G1/4" threads fit standard water-cooling components
  • Four Silver Shining fittings included for multi-point builds
  • RoHS compliant materials meet environmental safety standards

Multi-Link Fitting 4-Pack

This four-piece set provides G1/4" compression fittings built for 16mm OD rigid tubing in custom water-cooling loops. The brass construction and silver finish suit builders who want a clean, uniform look across multiple connection points. Each fitting is designed to join hard-tube runs securely while maintaining a consistent aesthetic.

Brass Construction and Multi-Link Design

The high-quality brass body resists corrosion and provides a solid sealing surface for compression rings. Multi-link geometry allows several fittings to be chained together, letting you extend or redirect tubing runs without extra adapters. The silver shining coating matches other Bitspower components for a cohesive appearance.

Installation Notes

Slide the compression ring and nut onto the tube, insert the tube fully into the fitting body, then tighten the nut by hand before a final quarter-turn with a wrench. The most common issue is an uneven tube cut that prevents a full seat, causing a slow leak when the loop is pressurised. Deburring the inside and outside edges of every 16mm cut eliminates this problem.

Helstu kostir

  • Multi-link design enables secure hard-tube extensions
  • High-quality brass construction ensures durable leak-free seals
  • G1/4" threads fit standard water-cooling components
  • Four Silver Shining fittings included for multi-point builds
  • RoHS compliant materials meet environmental safety standards

Tæknilýsing

TypeFittings

Spurningar um þessa vöru

Will the G1/4" threads on these multi-link fittings need periodic re-tightening or O-ring replacement over time?

The brass compression design seals against 16mm OD hard tubing with captive O-rings; inspect seals during loop maintenance and replace only if leakage appears.

What is the practical bending-radius limit when routing 16mm rigid tube between these fittings in a tight loop?

Each fitting adds roughly 16 mm of straight engagement, so allow at least that much straight run before the first bend to avoid stress on the compression seal.

Do the brass bodies and silver finish add noticeable heat or restrict flow when the loop runs continuously?

Brass conducts heat neutrally and the full-bore G1/4" channel adds negligible restriction; the fittings remain at coolant temperature with no audible noise.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.