Δεχόμαστε κρυπτονομίσματα — έτσι ώστε αυτά που κατέχετε να μπορούν να αγοράσουν πραγματικό εξοπλισμό.Πληρώστε σε κρυπτονομίσματα, ξοδέψτε τα σε πραγματικό εξοπλισμό. Δωρεάν ασφαλισμένη αποστολή παγκοσμίως άνω των 399 $. Ουδέτερες κούτες αποστολής, χωρίς σήμανση, από τη Γερμανία.Δωρεάν ασφαλισμένη αποστολή άνω των 399 $. Η ισοτιμία σας κλειδώνει για 30 λεπτά μόλις ανοίξει το ταμείο.Κλείδωμα ισοτιμίας 30 λεπτών. Κάθε προϊόν είναι σφραγισμένο, ελεγμένο ως προς τον σειριακό αριθμό του, και καλύπτεται από εγγύηση 24 μηνών.Σφραγισμένο, με εγγύηση 24 μηνών.

Παρακολουθούμενα είδη Σύνδεση
Green circuit board with M.2 slot and two HDMI ports

LORDWORLD

LORDWORLD PCIe to M.2 Multifunctional Adapter for Raspberry Pi 5 NVMe 2230 2242

SKU CH-7CB4-8AY43

Adds NVMe storage and dual 4K HDMI outputs to Raspberry Pi 5 via 16-pin PCIe, supporting 2230 and 2242 drives with Gen2 and Gen3 modes and boot capability, powered by USB-C or screw terminal

  • Adds fast NVMe storage to Raspberry Pi 5 via 16-pin PCIe link
  • Boots Raspberry Pi 5 directly from M.2 solid-state drive
  • Fits 2230 and 2242 size NVMe drives for flexible capacity
  • Converts dual micro HDMI to full-size HDMI for simpler monitor hookup
  • Powers the board through USB Type-C or screw terminals

Raspberry Pi 5 NVMe adapter

The LORDWORLD PCIe to M.2 adapter connects a Raspberry Pi 5 to NVMe solid-state drives through its 16-pin PCIe interface. It accepts 2230 and 2242 form-factor drives and supports Gen2 and Gen3 signalling. The board also converts the Pi’s micro-HDMI outputs to two full-size HDMI female ports for dual 4K display connectivity. Power can be supplied via USB Type-C or a screw terminal block.

MicroSD to NVMe boot upgrade

This adapter replaces the standard microSD card as the primary boot device, letting the Pi 5 start directly from a faster NVMe drive. The jump is worth it when applications demand quicker random I/O, shorter boot times or greater endurance than flash cards provide. Builders who need more storage capacity than the supported 2230 and 2242 drives offer should look elsewhere.

Straightforward HAT installation

The unit mounts on the Pi 5’s 16-pin PCIe connector using the included cable and aligns with the standard HAT mounting holes. No soldering or custom kernel builds are required; the Pi 5 firmware recognises the NVMe drive for booting once the latest bootloader is applied. Common issues include loose cable seating, insufficient power from the Type-C port under load, and forgetting to update the bootloader before first use.

Βασικά χαρακτηριστικά

  • Adds fast NVMe storage to Raspberry Pi 5 via 16-pin PCIe link
  • Boots Raspberry Pi 5 directly from M.2 solid-state drive
  • Fits 2230 and 2242 size NVMe drives for flexible capacity
  • Converts dual micro HDMI to full-size HDMI for simpler monitor hookup
  • Powers the board through USB Type-C or screw terminals

Προδιαγραφές

BrandLORDWORLD

Ερωτήσεις για αυτό το προϊόν

What physical clearance does the adapter need to fit a 2230 or 2242 M.2 NVMe drive?

The board accepts M.2 2230 and 2242 NVMe drives directly; no extra brackets or spacers are required beyond the drive length itself.

How is the 16-pin PCIe cable connected to the Raspberry Pi 5, and which step is commonly missed?

Plug the 16-pin cable into the Pi 5's PCIe FPC connector, then enable the PCIe interface in the boot config before the NVMe drive will be detected.

When should the M.2 NVMe drive be replaced, and what indicates it is wearing out?

Replace the drive when SMART health attributes show high wear-level counts or when sustained read/write speeds drop noticeably below expected NVMe performance.

Επίσης σε αυτό το ράφι

Οι πελάτες σύγκριναν και αυτά

Ίδιο ράφι, ίδιο ταμείο — οκτώ νομίσματα και κλείδωμα ισοτιμίας 30 λεπτών.