Δεχόμαστε κρυπτονομίσματα — έτσι ώστε αυτά που κατέχετε να μπορούν να αγοράσουν πραγματικό εξοπλισμό.Πληρώστε σε κρυπτονομίσματα, ξοδέψτε τα σε πραγματικό εξοπλισμό. Δωρεάν ασφαλισμένη αποστολή παγκοσμίως άνω των 399 $. Ουδέτερες κούτες αποστολής, χωρίς σήμανση, από τη Γερμανία.Δωρεάν ασφαλισμένη αποστολή άνω των 399 $. Η ισοτιμία σας κλειδώνει για 30 λεπτά μόλις ανοίξει το ταμείο.Κλείδωμα ισοτιμίας 30 λεπτών. Κάθε προϊόν είναι σφραγισμένο, ελεγμένο ως προς τον σειριακό αριθμό του, και καλύπτεται από εγγύηση 24 μηνών.Σφραγισμένο, με εγγύηση 24 μηνών.

Παρακολουθούμενα είδη Σύνδεση
Black 80mm square fan with hydraulic bearing and three-pin connector

OEM Industries

OEM Industries D08K-12PU 80mm 12V 0.19A 3-pin CPU cooler

SKU CH-RBQG-NR3VA

80 mm hydraulic-bearing fan runs at 12 V and 0.19 A with a 3-pin connector for CPU or case cooling

  • ColorBlack
  • TypeFan only
  • Fan Size80mm
  • Bearing TypeHydraulic
  • Power Connector3 Pin
  • LEDNo
  • 80 mm fan fits compact CPU cooler builds
  • Hydraulic bearing reduces noise and extends service life
  • 12 V 0.19 A draw keeps power demand low
  • 3-pin connector works with standard motherboard headers
  • NIDEC 8025 motor delivers reliable airflow for 8 cm cooling

80 mm hydraulic-bearing case fan

The OEM Industries D08K-12PU is an 80 mm square fan with a hydraulic bearing and a black frame. It draws 0.19 A at 12 V and connects through a standard three-pin header. The unit is sold as a fan only, without heatsink or mounting hardware for a specific processor socket. Builders who need a compact airflow source for tight chassis or legacy 80 mm mounts will find it a direct fit.

Fits three-pin headers and 80 mm mounts

Because the fan uses a three-pin power connector, it plugs straight into any motherboard or fan-controller header that supplies 12 V. Its 80 by 25 mm footprint matches the common 8025 mounting pattern used on many small-form-factor cases and older CPU coolers. The hydraulic bearing reduces friction compared with sleeve designs, helping the fan maintain consistent speed in confined spaces where cable routing is limited.

Low current draw and no LED lighting

At 0.19 A the fan adds only a small load to the 12 V rail, so it will not stress budget power supplies or dense fan arrays. The hydraulic bearing runs quietly at typical speeds, and the absence of LEDs eliminates light bleed in dark builds. No PWM control is present, so speed varies with voltage rather than a fourth-wire signal.

Βασικά χαρακτηριστικά

  • 80 mm fan fits compact CPU cooler builds
  • Hydraulic bearing reduces noise and extends service life
  • 12 V 0.19 A draw keeps power demand low
  • 3-pin connector works with standard motherboard headers
  • NIDEC 8025 motor delivers reliable airflow for 8 cm cooling

Προδιαγραφές

ModelD08K-12PU
ColorBlack
TypeFan only
Fan Size80mm
Bearing TypeHydraulic
Power Connector3 Pin
LEDNo

Ερωτήσεις για αυτό το προϊόν

What is the power draw of the 80mm D08K-12PU fan at 12V?

The fan draws 0.19 A at 12 V, so its power consumption is very low and heat output stays minimal during sustained use.

How much noise and heat does the hydraulic bearing produce during all-day operation?

The hydraulic bearing runs quietly and the low 0.19 A draw keeps waste heat small even when the fan runs continuously.

Which motherboard header is needed to connect the 3-pin D08K-12PU cooler?

A standard 3-pin fan header on the motherboard is required to power and control the cooler.

Επίσης σε αυτό το ράφι

Οι πελάτες σύγκριναν και αυτά

Ίδιο ράφι, ίδιο ταμείο — οκτώ νομίσματα και κλείδωμα ισοτιμίας 30 λεπτών.