Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Black 80mm square fan with hydraulic bearing and three-pin connector

OEM Industries

OEM Industries D08K-12PU 80mm 12V 0.19A 3-pin CPU cooler

SKU CH-RBQG-NR3VA

80 mm hydraulic-bearing fan runs at 12 V and 0.19 A with a 3-pin connector for CPU or case cooling

  • ColorBlack
  • TypeFan only
  • Fan Size80mm
  • Bearing TypeHydraulic
  • Power Connector3 Pin
  • LEDNo
  • 80 mm fan fits compact CPU cooler builds
  • Hydraulic bearing reduces noise and extends service life
  • 12 V 0.19 A draw keeps power demand low
  • 3-pin connector works with standard motherboard headers
  • NIDEC 8025 motor delivers reliable airflow for 8 cm cooling

80 mm hydraulic-bearing case fan

The OEM Industries D08K-12PU is an 80 mm square fan with a hydraulic bearing and a black frame. It draws 0.19 A at 12 V and connects through a standard three-pin header. The unit is sold as a fan only, without heatsink or mounting hardware for a specific processor socket. Builders who need a compact airflow source for tight chassis or legacy 80 mm mounts will find it a direct fit.

Fits three-pin headers and 80 mm mounts

Because the fan uses a three-pin power connector, it plugs straight into any motherboard or fan-controller header that supplies 12 V. Its 80 by 25 mm footprint matches the common 8025 mounting pattern used on many small-form-factor cases and older CPU coolers. The hydraulic bearing reduces friction compared with sleeve designs, helping the fan maintain consistent speed in confined spaces where cable routing is limited.

Low current draw and no LED lighting

At 0.19 A the fan adds only a small load to the 12 V rail, so it will not stress budget power supplies or dense fan arrays. The hydraulic bearing runs quietly at typical speeds, and the absence of LEDs eliminates light bleed in dark builds. No PWM control is present, so speed varies with voltage rather than a fourth-wire signal.

Põhijooned

  • 80 mm fan fits compact CPU cooler builds
  • Hydraulic bearing reduces noise and extends service life
  • 12 V 0.19 A draw keeps power demand low
  • 3-pin connector works with standard motherboard headers
  • NIDEC 8025 motor delivers reliable airflow for 8 cm cooling

Tehnilised andmed

ModelD08K-12PU
ColorBlack
TypeFan only
Fan Size80mm
Bearing TypeHydraulic
Power Connector3 Pin
LEDNo

Küsimused selle toote kohta

What is the power draw of the 80mm D08K-12PU fan at 12V?

The fan draws 0.19 A at 12 V, so its power consumption is very low and heat output stays minimal during sustained use.

How much noise and heat does the hydraulic bearing produce during all-day operation?

The hydraulic bearing runs quietly and the low 0.19 A draw keeps waste heat small even when the fan runs continuously.

Which motherboard header is needed to connect the 3-pin D08K-12PU cooler?

A standard 3-pin fan header on the motherboard is required to power and control the cooler.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.