Raspberry Pi

Raspberry Pi SC1166 M.2 HAT+ development board

SKU CH-Q60P-0BTWS

Adds M.2 M-key 2230 or 2242 devices to Raspberry Pi 5 via PCIe 2.0 at 500 MB/s peak

Adds M.2 M-key storage or AI accelerators to Raspberry Pi 5 via PCIe 2.0
Peak transfer rate of 500 MB/s over single-lane PCIe 2.0 interface
Fits 2230 and 2242 form-factor M.2 devices
Powers M.2 peripherals with up to 3 A and includes status LEDs
Ships with ribbon cable, 16 mm stacking header, spacers, screws and M.2 retainer

36,99 $

0.00047283 BTC με τη σημερινή ισοτιμία

Διαθέσιμο · αποστολή σήμερα

Το ταμείο κλειδώνει την ισοτιμία σας για 30 λεπτά.

Παράδοση προς Ηνωμένες Πολιτείες εκτίμηση

UPS Worldwide Expedited 3–6 εργάσιμες ημέρες 39,90 $
DHL Express Worldwide 2–3 εργάσιμες ημέρες 74,90 $

Προσθέστε 362,01 $ ακόμη και η βασική αποστολή γίνεται δωρεάν.

Οι εισαγωγικοί δασμοί επιβάλλονται κατά την άφιξη από τη χώρα σας.

Αποστολή αλλού

M.2 HAT+ for Raspberry Pi 5

The SC1166 board adds a single-lane PCIe 2.0 interface to the Raspberry Pi 5, enabling M.2 M-key devices in 2230 or 2242 form factors. It conforms to the HAT+ specification and ships with a ribbon cable, stacking header, spacers and screws. The board can deliver up to 3A to the attached peripheral and includes power and activity LEDs.

Ideal for storage and AI add-ons

Developers needing NVMe storage or an AI accelerator on a Pi 5 will find this HAT+ a direct fit. Builders who require multiple M.2 slots, larger 2280 devices, or a different single-board computer cannot use this board. Projects without a Pi 5 PCIe connector should look elsewhere.

Single-lane PCIe 2.0 at 500 MB/s peak

The sole high-speed link is a single-lane PCIe 2.0 connection rated at 500 MB/s peak transfer rate. This bandwidth ceiling determines whether a specific NVMe drive or accelerator can perform as expected. Verify your peripheral's throughput needs against this limit before purchasing.

Βασικά χαρακτηριστικά

Adds M.2 M-key storage or AI accelerators to Raspberry Pi 5 via PCIe 2.0
Peak transfer rate of 500 MB/s over single-lane PCIe 2.0 interface
Fits 2230 and 2242 form-factor M.2 devices
Powers M.2 peripherals with up to 3 A and includes status LEDs
Ships with ribbon cable, 16 mm stacking header, spacers, screws and M.2 retainer

Προδιαγραφές

Δεν έχουν δημοσιευτεί ακόμη προδιαγραφές για αυτό το προϊόν.

Ερωτήσεις για αυτό το προϊόν

Will the SC1166 M.2 HAT+ fit on my existing Raspberry Pi 5 without blocking other ports?

The board follows the Raspberry Pi HAT+ specification and uses a 16 mm stacking header, so it sits above the Pi 5’s GPIO header while leaving the other connectors accessible.

How can I confirm the PCIe 2.0 link is running at the expected 500 MB/s after I install an M.2 device?

Check the kernel log for the negotiated link speed and run a storage benchmark such as fio; a single-lane PCIe 2.0 connection should show throughput close to 500 MB/s.

Which mounting parts come in the box and do I need to buy any extra screws for a 2242 drive?

The package includes a ribbon cable, 16 mm stacking header, threaded spacers, standard screws and a knurled double-flanged screw that secures both 2230 and 2242 form-factor devices; no extra hardware is required.

Επίσης σε αυτό το ράφι