Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Black 16mm hard-tube compression fitting with nylon insert, G1/4 thread

Alphacool

Alphacool Eiszapfen PRO 16mm HardTube Fitting G1/4 Deep Black 1017616

SKU CH-FBVJ-QH2AE

G1/4 hard-tube fitting with internal nylon inserts that prevent 16 mm PETG deformation at 60 °C and withstand over 8 kg pull force

  • ColorBlack
  • FeaturesThe new Eiszapfen PRO HardTube fittings from Alphacool are a
  • Prevents PETG tube deformation at 60 °C with internal nylon inserts
  • Larger compression seal contact area secures tube from inside and outside
  • Withstands tensile loads over 8 kg so HardTube will not slip
  • G1/4 thread fits standard 16 mm hard-tube loops
  • Deep Black finish matches dark-themed builds

Hard-tube fitting for 16 mm PETG loops

The Alphacool Eiszapfen PRO is a G1/4 compression fitting designed for 16 mm PETG hard tubing in custom water-cooling builds. It targets builders who want a secure seal without relying on standard O-ring pressure alone. The deep black finish matches dark-themed loops. A single fitting is supplied in the package.

Nylon insert reinforces tube against heat

The fitting uses an internal nylon insert that stabilises the hard tube from the inside while a compression seal grips the outside. This dual reinforcement prevents the tube from slipping even when coolant temperatures approach 60 °C, where PETG can begin to soften. The larger contact area of the seal improves hold compared with conventional O-rings. No special tools are required beyond standard G1/4 threading.

Tested to over 8 kg tensile load

Alphacool reports the joint withstands more than 8 kg of pulling force, giving ample headroom for vibration or case movement. The design is not recommended for use with Bitspower brand tubing, so builders using that tubing should choose a different fitting. The fitting adds no flow restriction beyond the normal G1/4 port. It suits single-loop builds where long PETG runs must stay rigid.

Põhijooned

  • Prevents PETG tube deformation at 60 °C with internal nylon inserts
  • Larger compression seal contact area secures tube from inside and outside
  • Withstands tensile loads over 8 kg so HardTube will not slip
  • G1/4 thread fits standard 16 mm hard-tube loops
  • Deep Black finish matches dark-themed builds

Tehnilised andmed

BrandAlphacool
Model1017616
Part Number1017616
ColorBlack
FeaturesThe new Eiszapfen PRO HardTube fittings from Alphacool are a further development of the well-known, previous Eiszapfen.

Küsimused selle toote kohta

At what temperature can the PETG hard tube start to deform inside this fitting?

The PETG hard tube can begin to deform at 60 °C, which the Eiszapfen PRO fitting is designed to prevent by using internal nylon inserts that stabilise the tube.

How much heat or noise does this fitting generate during continuous operation?

The fitting itself produces no heat or noise; it is a passive brass component that simply secures the tubing within the liquid-cooling loop.

What tubing size and thread standard must I already have for this fitting to work?

You need 16 mm outer-diameter PETG hard tube and a component with a G1/4 female thread to accept the fitting.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.