Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Black sleeved 12-inch splitter cable with one 3-pin female and two 3-pin male connectors

EN-Labs

EN-Labs 3PINSPL212 1-to-2 3-pin fan power splitter cable 12 inch black sleeved

SKU CH-D473-32S3S

A 12-inch black sleeved cable splits one 3-pin header into two fan connectors for extra cooling

  • TypeCable Splitters
  • ColorBlack
  • Length11" - 15"
  • SpecificationsType :PWM fan power cable Length: 12 inches Conductor:26AWG
  • Connector Number3
  • Terminal GenderFemale to Male
  • Connect two 3-pin fans to one header for expanded cooling
  • 12-inch length gives flexible fan placement inside the case
  • Black net-jacket sleeve protects wires and keeps build tidy
  • 26AWG copper conductors deliver reliable 12V or 5V power
  • Works with 4-pin PWM fans when speed control is not needed

Splitter for two 3-pin fans

This EN-Labs cable splits one motherboard 3-pin header into two 3-pin connectors so you can run a pair of case fans from a single fan header. It supports both 12 V and 5 V fans and accepts 4-pin PWM fans, though the PWM speed-control function is not passed through. The 12-inch length gives enough reach for typical chassis layouts without excess slack. Builders who need more than two fans on one header will need a different solution.

Black net-jacket sleeve and 26 AWG copper

The cable uses 26 AWG copper conductors wrapped in a black net-jacket sleeve that resists abrasion and keeps the wiring tidy behind the motherboard tray. A single 3-pin TX3 female connector plugs into the board or a PSU adapter, while two 3-pin TX3 male ends attach to the fans. The sleeve adds a clean look and helps prevent snagging on sharp case edges during assembly.

No extra accessories or software included

The package contains only the splitter cable itself; there are no mounting clips, Velcro ties or configuration utilities supplied. Installation is purely plug-and-play, so no driver or firmware steps are required. Users who want cable-management hardware will need to source it separately.

Põhijooned

  • Connect two 3-pin fans to one header for expanded cooling
  • 12-inch length gives flexible fan placement inside the case
  • Black net-jacket sleeve protects wires and keeps build tidy
  • 26AWG copper conductors deliver reliable 12V or 5V power
  • Works with 4-pin PWM fans when speed control is not needed

Tehnilised andmed

BrandEn-Labs
Model3PINSPL212
TypeCable Splitters
ColorBlack
Length11" - 15"
SpecificationsType :PWM fan power cable
Length: 12 inches
Conductor:26AWG Copper
Connector A:1 x 3pin fan TX3 female
Connector B: 2 x 3pin Fan TX3 male
Power supports:12V/5V fans
Connector Number3
Terminal GenderFemale to Male
FeaturesThis TX3 Fan Power Splitter Cable lets you connect two 3-pin (TX3) fans to a single power supply connector, allowing you to optimize your cooling capability without having to upgrade the power supply.
Use this 1 x 3-pin motherboard header to power 2 x cooling fans with 3-pin connector
6-inch long, female end 3-pin header plugs on to motherboard (or 3-pin male connector from power supply), 2 x 3-pin male headers to cooling fans
Providing a flexible way to position computer case fans as needed, the TX3 Fan Power Splitter cable offers a connection length of 6 inches, eliminating the nee

Küsimused selle toote kohta

Does the 3-pin TX3 header on this splitter carry a PWM signal to both fans?

The cable is described as a PWM fan power cable, but the note states it works with 4-pin PWM fans with no PWM function, so the 3-pin TX3 connectors pass power only and do not carry a PWM signal.

What clearance is needed for the black net-jacket sleeving and the 12-inch cable run?

The splitter uses 22AWG copper conductors wrapped in a black net-jacket sleeve and is 12 inches long, so allow enough space for the sleeve diameter and the full cable length when routing between the motherboard header and the two fans.

How do you attach the splitter so the single female end connects to the motherboard and the two male ends go to the fans?

Plug the one 3-pin TX3 female connector onto the motherboard fan header or a 3-pin male lead from the power supply, then connect each 3-pin TX3 male connector to a fan; the step often missed is ensuring the female end is fully seated on the header before powering on.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.