Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Clear plastic spool holding translucent off-white 1.75 mm PVA filament coil

Lay Filaments

Lay Filaments LAYaPVA PVA Filament 1.75 mm 0.75 kg

SKU CH-3RK4-KXM9H

Water-soluble PVA support filament in 1.75 mm diameter with ±0.1 mm tolerance, prints at 190-210 °C and dissolves in water

  • Dissolves in cold or warm water for clean support removal
  • Compatible with PLA, ABS and Nylon for versatile dual-extrusion prints
  • ±0.1 mm diameter tolerance ensures consistent extrusion
  • Prints at 190–210 °C without heated bed requirement
  • 75 kg spool in 1.75 mm and 2.85 mm sizes

Soluble Support Filament for Dual-Extrusion Printing

Lay Filaments LAYaPVA is a water-soluble PVA filament designed as a carrier material for dual-extrusion printers. It adheres well to PLA, ABS and Nylon during the build and dissolves completely in cold or warm water after printing. The material leaves no residue on the finished part, making it suited for complex geometries that require internal supports.

Thermal Resistance and Print Settings

The formulation is engineered to resist heat distortion and thermal degradation inside the extruder better than standard PVA grades. Printing temperature is 190 - 210 degC with a diameter tolerance of ± 0.1 mm. No heated bed is required for the support material itself, reducing setup complexity for multi-material jobs.

Dissolution Behaviour Under Sustained Use

Submerging the finished print in cold water dissolves the support structures fully in about two hours; warm water accelerates the process. The filament is supplied on a 0.75 kg spool with a 2.85 mm diameter. Buyers using 1.75 mm extruders or requiring larger spool weights will need a different product.

Põhijooned

  • Dissolves in cold or warm water for clean support removal
  • Compatible with PLA, ABS and Nylon for versatile dual-extrusion prints
  • ±0.1 mm diameter tolerance ensures consistent extrusion
  • Prints at 190–210 °C without heated bed requirement
  • 75 kg spool in 1.75 mm and 2.85 mm sizes

Tehnilised andmed

BrandLay Filaments

Küsimused selle toote kohta

How do I install the 1.75 mm Lay Filaments LAYaPVA filament without clogging?

Load the filament at 190 – 210 °C, ensure the Bowden tube or direct drive path is clean, and purge until only clear PVA extrudes; the step many miss is drying the spool first because PVA absorbs moisture rapidly.

What maintenance or replacement will the 0.75 kg Lay Filaments LAYaPVA spool need later?

Store unused filament in a sealed bag with desiccant; if it becomes brittle or prints with bubbles, dry it at low heat or replace the spool — no other consumable parts are involved.

What is the first limit that appears during a long print with Lay Filaments LAYaPVA?

Thermal degradation inside the extruder during extended printing; the filament is formulated to resist heat distortion up to 210 °C, but prolonged exposure beyond that range causes breakdown.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.