Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Coil of soft PLA 3D printer filament 3.0mm 0.25kg

Lay Filaments

Lay Filaments PLA-Y-Soft 3D printer filament 3.0mm 0.25kg

SKU CH-KCD9-6RY4X

Soft PLA filament prints at 225–240 °C on a cold bed with low warp and a high bioplastic content

  • Easy cold-bed printing with minimal warping
  • Eco-friendly high bioplastic content
  • Reliable standard PLA for everyday prints
  • Extrudes at 225-240 °C without heated bed
  • 0 mm diameter suits compatible printers

Soft PLA filament for hobbyists

This 3.0 mm diameter PLA-Y-Soft spool contains 0.25 kg of bioplastic-rich material. It is aimed at makers who prefer a forgiving feedstock for everyday prints. The formulation prints at moderate temperatures between 225 and 240 °C and adheres well to a cold bed. Its renewable composition suits users who value an environmentally friendly supply.

Steady extrusion on long prints

Because the polymer softens without demanding high heat, the nozzle maintains a stable melt zone during extended sessions. Low warp on an unheated build plate means corners stay down even when the printer runs for hours. The consistent diameter reduces the risk of feed slipping that can ruin a multi-hour job. Users can rely on repeatable layer adhesion throughout the build.

Limits of cold-bed PLA printing

Without a heated chamber the material cannot match the dimensional stability of high-temperature polymers on large flat parts. Overhangs and bridges may sag if cooling is insufficient, since the soft formulation stays pliable longer. The 0.25 kg spool length restricts uninterrupted print volume to smaller models. Buyers who need engineering-grade heat resistance or continuous multi-kilogram runs should look elsewhere.

Põhijooned

  • Easy cold-bed printing with minimal warping
  • Eco-friendly high bioplastic content
  • Reliable standard PLA for everyday prints
  • Extrudes at 225-240 °C without heated bed
  • 0 mm diameter suits compatible printers

Tehnilised andmed

BrandLay Filaments

Küsimused selle toote kohta

How much power does the hot-end draw when printing PLA-Y-Soft at 240 degC all day?

The filament prints at 225-240 degC; actual power draw depends on your printer's heater cartridge and firmware settings, not on the filament itself.

What printer hardware is required to use 3.0mm PLA-Y-Soft?

You need a 3D printer with a 3.0mm filament path, a hot-end that reaches at least 240 degC, and a drive gear sized for 3.0mm stock.

Will PLA-Y-Soft stick to the PEI sheet on my older printer without a heated bed?

Yes, the material is formulated for low warp on a cold bed, so it adheres well to PEI, glass or tape without bed heat.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.