Sprejemamo kriptovalute — tako lahko sredstva, ki jih imate, kupijo pravo strojno opremo.Plačajte v kriptovaluti, zapravite jo za pravo strojno opremo. Brezplačna zavarovana dostava po vsem svetu nad 399 $. Nevtralni kartoni brez znamke, poslani iz Nemčije.Brezplačna zavarovana dostava nad 399 $. Vaš tečaj je zaklenjen za 30 minut, takoj ko se odpre blagajna.Tečaj zaklenjen 30 minut. Vsak izdelek je zapečaten, njegova serijska številka preverjena, in krit z 24-mesečno garancijo.Zapečateno, 24-mesečna garancija.

Spremljani izdelki Prijava
Coil of soft PLA 3D printer filament 3.0mm 0.25kg

Lay Filaments

Lay Filaments PLA-Y-Soft 3D printer filament 3.0mm 0.25kg

SKU CH-KCD9-6RY4X

Soft PLA filament prints at 225–240 °C on a cold bed with low warp and a high bioplastic content

  • Easy cold-bed printing with minimal warping
  • Eco-friendly high bioplastic content
  • Reliable standard PLA for everyday prints
  • Extrudes at 225-240 °C without heated bed
  • 0 mm diameter suits compatible printers

Soft PLA filament for hobbyists

This 3.0 mm diameter PLA-Y-Soft spool contains 0.25 kg of bioplastic-rich material. It is aimed at makers who prefer a forgiving feedstock for everyday prints. The formulation prints at moderate temperatures between 225 and 240 °C and adheres well to a cold bed. Its renewable composition suits users who value an environmentally friendly supply.

Steady extrusion on long prints

Because the polymer softens without demanding high heat, the nozzle maintains a stable melt zone during extended sessions. Low warp on an unheated build plate means corners stay down even when the printer runs for hours. The consistent diameter reduces the risk of feed slipping that can ruin a multi-hour job. Users can rely on repeatable layer adhesion throughout the build.

Limits of cold-bed PLA printing

Without a heated chamber the material cannot match the dimensional stability of high-temperature polymers on large flat parts. Overhangs and bridges may sag if cooling is insufficient, since the soft formulation stays pliable longer. The 0.25 kg spool length restricts uninterrupted print volume to smaller models. Buyers who need engineering-grade heat resistance or continuous multi-kilogram runs should look elsewhere.

Poudarki

  • Easy cold-bed printing with minimal warping
  • Eco-friendly high bioplastic content
  • Reliable standard PLA for everyday prints
  • Extrudes at 225-240 °C without heated bed
  • 0 mm diameter suits compatible printers

Specifikacije

BrandLay Filaments

Vprašanja o tem izdelku

How much power does the hot-end draw when printing PLA-Y-Soft at 240 degC all day?

The filament prints at 225-240 degC; actual power draw depends on your printer's heater cartridge and firmware settings, not on the filament itself.

What printer hardware is required to use 3.0mm PLA-Y-Soft?

You need a 3D printer with a 3.0mm filament path, a hot-end that reaches at least 240 degC, and a drive gear sized for 3.0mm stock.

Will PLA-Y-Soft stick to the PEI sheet on my older printer without a heated bed?

Yes, the material is formulated for low warp on a cold bed, so it adheres well to PEI, glass or tape without bed heat.

Tudi v tem oddelku

Stranke so primerjale tudi te

Ista polica, ista blagajna — osem kriptovalut in 30-minutni zaklep tečaja.