Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Small transparent OLED board 1.51 inch 128 by 64 light blue

LORDWORLD

LORDWORLD 1.51inch Transparent OLED Display Module 128×64 Light Blue

SKU CH-VHRR-5QXQB

A 1.51 inch transparent OLED module with a 128×64 light blue display, embedded driver chip, and SPI or I2C interfaces for Raspberry Pi, Arduino, and STM32

  • Transparent 1.51inch OLED lets light through for see‑through UI projects
  • 128×64 pixel resolution renders crisp light‑blue graphics and text
  • Embedded driver chip handles panel timing without extra MCU load
  • SPI and I2C interfaces connect directly to Raspberry Pi, Arduino or STM32
  • Full viewing angle keeps content readable from any direction

1.51″ Transparent OLED for Makers

The LORDWORLD module is a 1.51inch transparent OLED display with a 128×64 resolution and light blue emission. It targets hobbyists and engineers building Raspberry Pi, Arduino or STM32 projects that need a see-through readout. The board ships new and includes an embedded driver chip to simplify integration.

SPI and I2C Dual Interface

The single specification that decides fit is the combined 4-wire SPI and I2C interface on one module. This dual option lets the display talk to almost any microcontroller without extra level-shifting hardware. If your host board lacks either bus, this part will not connect.

Embedded Driver Frees GPIO

Because the driver chip lives on the module, the host controller only needs the serial bus lines and power. No parallel data lines or timing-critical bit-banging are required, leaving more GPIO free for sensors or actuators. Development examples for the three supported platforms are available from the supplier.

Põhijooned

  • Transparent 1.51inch OLED lets light through for see‑through UI projects
  • 128×64 pixel resolution renders crisp light‑blue graphics and text
  • Embedded driver chip handles panel timing without extra MCU load
  • SPI and I2C interfaces connect directly to Raspberry Pi, Arduino or STM32
  • Full viewing angle keeps content readable from any direction

Tehnilised andmed

BrandLORDWORLD

Küsimused selle toote kohta

How does the 128×64 resolution look on the 1.51 inch transparent panel?

The 1.51 inch transparent OLED shows light blue graphics at 128×64 pixels, giving a crisp readout for status icons or sensor values in a compact see-through area.

What do the SPI and I2C interfaces limit in practice?

The module supports both 4-wire SPI and I2C, so you can choose the faster SPI path or the simpler two-wire I2C bus depending on your host board.

What mounting holes or connectors does the board need to fit a project?

The display ships as a bare module with a pin header for SPI/I2C; it has no mounting holes, so you secure it with a custom bracket or hot-melt adhesive in your enclosure.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.