Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Small rectangular e-paper display module, 2.66inch, red black white, SPI pins visible

LORDWORLD

LORDWORLD 2.66inch E-Paper Display Module (B) 296×152 SPI

SKU CH-WRY8-276NW

A 2.66 inch three-colour e-paper screen that holds its image without power and draws current only during refresh over an SPI link compatible with 3.3 V and 5 V logic

  • Retains image without power thanks to no backlight
  • Ultra-low power draw — only needed during refresh
  • 296×152 pixel resolution in red, black and white
  • SPI interface connects to Raspberry Pi, Jetson Nano, STM32
  • Onboard voltage translator supports 3.3 V and 5 V MCUs

2.66inch E-Paper Module for Makers

This 2.66inch E-Paper display module offers a 296×152 pixel resolution with red, black and white three-colour output. It connects via SPI and includes an onboard voltage translator for 3.3V or 5V microcontrollers. The panel retains its last image without power and draws energy only during refresh cycles.

Suits low-power IoT prototypes and badge projects

Developers building battery-powered sensors, shelf labels or conference badges will benefit from the ultra-low consumption and persistent display. Projects that require video-rate animation, full-colour graphics or a backlit screen should consider a different display technology.

Check SPI pins and 3.3V or 5V logic compatibility

Verify that your host board exposes a hardware SPI bus and that its I/O voltage matches the module's 3.3V or 5V tolerance. Ensure your firmware can drive the required refresh sequence and that the physical outline fits your enclosure.

Põhijooned

  • Retains image without power thanks to no backlight
  • Ultra-low power draw — only needed during refresh
  • 296×152 pixel resolution in red, black and white
  • SPI interface connects to Raspberry Pi, Jetson Nano, STM32
  • Onboard voltage translator supports 3.3 V and 5 V MCUs

Tehnilised andmed

BrandLORDWORLD

Küsimused selle toote kohta

Which controller board and SPI pins do I need to drive this 2.66inch 296×152 display?

Connect the module to a Raspberry Pi, Jetson Nano, STM32 or any 3.3V / 5V MCU using its SPI interface; the onboard voltage translator handles level shifting automatically.

Will the three-colour red/black/white panel work if I keep using my older 3.3V microcontroller?

Yes, the built-in voltage translator makes the display fully compatible with 3.3V logic, so legacy MCUs can drive it without extra circuitry.

How can I verify the 296×152 panel is refreshing correctly after wiring it up?

Power the board, send a test image over SPI and confirm the screen shows red, black and white pixels holding their state without a backlight.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.