Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Small rectangular e-paper display module, 2.66inch, red black white, SPI pins visible

LORDWORLD

LORDWORLD 2.66inch E-Paper Display Module (B) 296×152 SPI

SKU CH-WRY8-276NW

A 2.66 inch three-colour e-paper screen that holds its image without power and draws current only during refresh over an SPI link compatible with 3.3 V and 5 V logic

  • Retains image without power thanks to no backlight
  • Ultra-low power draw — only needed during refresh
  • 296×152 pixel resolution in red, black and white
  • SPI interface connects to Raspberry Pi, Jetson Nano, STM32
  • Onboard voltage translator supports 3.3 V and 5 V MCUs

2.66inch E-Paper Module for Makers

This 2.66inch E-Paper display module offers a 296×152 pixel resolution with red, black and white three-colour output. It connects via SPI and includes an onboard voltage translator for 3.3V or 5V microcontrollers. The panel retains its last image without power and draws energy only during refresh cycles.

Suits low-power IoT prototypes and badge projects

Developers building battery-powered sensors, shelf labels or conference badges will benefit from the ultra-low consumption and persistent display. Projects that require video-rate animation, full-colour graphics or a backlit screen should consider a different display technology.

Check SPI pins and 3.3V or 5V logic compatibility

Verify that your host board exposes a hardware SPI bus and that its I/O voltage matches the module's 3.3V or 5V tolerance. Ensure your firmware can drive the required refresh sequence and that the physical outline fits your enclosure.

Kohokohdat

  • Retains image without power thanks to no backlight
  • Ultra-low power draw — only needed during refresh
  • 296×152 pixel resolution in red, black and white
  • SPI interface connects to Raspberry Pi, Jetson Nano, STM32
  • Onboard voltage translator supports 3.3 V and 5 V MCUs

Tekniset tiedot

BrandLORDWORLD

Kysymyksiä tästä tuotteesta

Which controller board and SPI pins do I need to drive this 2.66inch 296×152 display?

Connect the module to a Raspberry Pi, Jetson Nano, STM32 or any 3.3V / 5V MCU using its SPI interface; the onboard voltage translator handles level shifting automatically.

Will the three-colour red/black/white panel work if I keep using my older 3.3V microcontroller?

Yes, the built-in voltage translator makes the display fully compatible with 3.3V logic, so legacy MCUs can drive it without extra circuitry.

How can I verify the 296×152 panel is refreshing correctly after wiring it up?

Power the board, send a test image over SPI and confirm the screen shows red, black and white pixels holding their state without a backlight.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.