BFKK
BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
214,99 $
0.00278925BTC
Laos
NEMIX RAM
NEMIX RAM 8GB DDR4 2400 CL17 1.2V 260-PIN SODIMM QNAP TVS-472XT TVS-672XT TVS-872XT memory upgrade
8GB DDR4 2400 SODIMM for QNAP TVS-472XT, TVS-672XT and TVS-872XT NAS systems
- Capacity8GB
- SpeedDDR4 2400 (PC4 19200)
- ECCNo
- Buffered/RegisteredUnbuffered
- ChipsetMajor OEM Samsung, Micron, Hynix
- Voltage1.20V
- 8GB capacity expands NAS memory for heavier workloads
- DDR4 2400 speed matches QNAP TVS-472XT, TVS-672XT, TVS-872XT specs
- 2V low voltage reduces power draw and heat
- CL17 latency supports responsive multitasking on compatible NAS
- 260-pin SODIMM form factor fits QNAP NAS memory slots
NEMIX 8 GB DDR4 SODIMM for QNAP NAS
This 8 GB DDR4 2400 MHz SODIMM is built for QNAP TVS-472XT, TVS-672XT and TVS-872XT units. It runs at 1.2 V with CL17 latency and uses a 260-pin unbuffered non-ECC design. The module adds capacity to supported NAS appliances without requiring configuration changes.
Suits owners expanding memory in listed QNAP models
The stick is made for the three TVS-XT series NAS devices named above. It will not fit systems that need ECC, registered DIMMs, 288-pin desktop memory or a different DDR generation. Buyers with other QNAP series or non-QNAP hardware should verify their platform requirements first.
Single-module kit simplifies installation
The package contains one 8 GB SODIMM, so you can populate a single slot or add to an existing bank. No extra cables, brackets or software are included. The memory is tested for compatibility with the target NAS units, letting you upgrade by inserting the module and restarting the device.
Põhijooned
- 8GB capacity expands NAS memory for heavier workloads
- DDR4 2400 speed matches QNAP TVS-472XT, TVS-672XT, TVS-872XT specs
- 2V low voltage reduces power draw and heat
- CL17 latency supports responsive multitasking on compatible NAS
- 260-pin SODIMM form factor fits QNAP NAS memory slots
Tehnilised andmed
| Brand | NEMIX RAM |
|---|---|
| Series | QNAP NAS Compatible Series Memory |
| Model | QNAP DDR4 2666MHZ Non-ECC Unbuffered SODIMM NAS Memory |
| Part Number | MS19200-818K1 |
| Capacity | 8GB |
| Speed | DDR4 2400 (PC4 19200) |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Voltage | 1.20V |
| Compatible System | Qnap |
| CAS Latency | CL17 |
| Heat Spreader | No |
| Type | 260-PIN DDR4 SODIMM |
| Rank | 1Rx8 |
| Features | DDR4 Non-ECC Unbuffered SODIMM Motherboard Compatible |
| Package Content | 8GB (1X8GB) DDR4 2400MHZ PC4-19200 2Rx8 1.2V CL17 260-PIN Non-ECC Unbuffered SODIMM |
Küsimused selle toote kohta
What QNAP NAS models must I already own for this 260-pin SODIMM to be compatible?
This module is validated for the QNAP TVS-472XT, TVS-672XT and TVS-872XT series.
How will the CL17 2400 MHz sticks behave if I keep my existing 2666 MHz modules installed?
The system will run all memory at the lowest common speed, so the faster modules will operate at 2400 MHz with CL17 timings.
How can I confirm the 8 GB module is recognised at 2400 MHz after installation?
Open the QNAP Control Panel, go to System > Hardware and verify the memory line shows 2400 MT/s and the correct total capacity.
Veel samast osakonnast
Kliendid võrdlesid neid ka
Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.
