Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Cylindrical coated brass extension coupler with male and female G 1/4 inch threads, 40mm body length, knurled grip surface

PrimoChill

PrimoChill Male-Female G1/4in 40mm SX Extension Coupler

SKU CH-NDQK-BCXTX

A G 1/4in male-to-female extension coupler adds 40 mm of clearance between water-cooling fittings and is made from coated brass with a pre-installed O-ring

  • TypeCPU Block

Option UV Orange

Näita veel 9 konfiguratsiooni

Läbikriipsutatud versioonid on olemas, kuid neid pole siin saadaval.

  • Adds 40 mm spacing for tight builds
  • Male-to-female G 1/4 in thread fits standard fittings
  • 45 mm overall height clears bulky components
  • Coated brass resists corrosion in coolant loops
  • Includes installed O-ring for leak-free seal

Extension coupler for custom loops

The PrimoChill Male-Female G1/4in 40mm SX Extension Coupler adds clearance between a component and a fitting in a custom water-cooling loop. It provides a single male and a single female G 1/4in thread in a coated brass body. The overall height with thread is 45mm and 40mm without. An O-ring is pre-installed on the male side.

For builders needing extra thread reach

This coupler suits anyone who finds a standard fitting too short to clear a block, radiator port or reservoir inlet. It is not intended for builders who need an angled adapter, a rotary joint or a longer extension than 40mm. It also does not replace a dedicated drain valve or a quick-disconnect fitting.

Check thread compatibility and clearance

Verify that every component you plan to connect uses a G 1/4in thread before ordering. Measure the available gap in your loop to confirm the 45mm overall height will fit without stressing adjacent tubing or fittings. Ensure the coated brass finish is acceptable alongside other metals in your coolant path.

Põhijooned

  • Adds 40 mm spacing for tight builds
  • Male-to-female G 1/4 in thread fits standard fittings
  • 45 mm overall height clears bulky components
  • Coated brass resists corrosion in coolant loops
  • Includes installed O-ring for leak-free seal

Tehnilised andmed

TypeCPU Block

Selle mudeli teised versioonid

5 veel samast sarjast

Sama seeria, erinev mälumaht, jahutus või taktsagedus — võrrelge enne otsustamist.

Küsimused selle toote kohta

What G 1/4in threaded components do I already need to connect this 40mm SX extension coupler?

You need at least one male G 1/4in fitting and one female G 1/4in port, such as on a water block, radiator, pump or reservoir, to thread the coupler between them.

Will the 45mm overall height with threads fit alongside my existing G 1/4in fittings in a tight loop?

The coupler adds 40mm of body length plus thread engagement, so measure the gap between your current fittings; if the clearance exceeds roughly 45mm it will fit without forcing adjacent tubing.

How can I confirm the coated brass coupler is sealed and oriented correctly after installation?

The male side ships with an installed O-ring; hand-tighten until the O-ring compresses, then pressure-test the loop — no leaks and proper alignment mean it is working as intended.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.