Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Cylindrical coated brass extension coupler with male and female G 1/4 inch threads, 40mm body length, knurled grip surface

PrimoChill

PrimoChill Male-Female G1/4in 40mm SX Extension Coupler

SKU CH-NDQK-BCXTX

A G 1/4in male-to-female extension coupler adds 40 mm of clearance between water-cooling fittings and is made from coated brass with a pre-installed O-ring

  • TypeCPU Block

Option UV Orange

Näytä 9 muuta kokoonpanoa

Yliviivatut versiot ovat olemassa, mutta niitä ei ole varastossa täällä.

  • Adds 40 mm spacing for tight builds
  • Male-to-female G 1/4 in thread fits standard fittings
  • 45 mm overall height clears bulky components
  • Coated brass resists corrosion in coolant loops
  • Includes installed O-ring for leak-free seal

Extension coupler for custom loops

The PrimoChill Male-Female G1/4in 40mm SX Extension Coupler adds clearance between a component and a fitting in a custom water-cooling loop. It provides a single male and a single female G 1/4in thread in a coated brass body. The overall height with thread is 45mm and 40mm without. An O-ring is pre-installed on the male side.

For builders needing extra thread reach

This coupler suits anyone who finds a standard fitting too short to clear a block, radiator port or reservoir inlet. It is not intended for builders who need an angled adapter, a rotary joint or a longer extension than 40mm. It also does not replace a dedicated drain valve or a quick-disconnect fitting.

Check thread compatibility and clearance

Verify that every component you plan to connect uses a G 1/4in thread before ordering. Measure the available gap in your loop to confirm the 45mm overall height will fit without stressing adjacent tubing or fittings. Ensure the coated brass finish is acceptable alongside other metals in your coolant path.

Kohokohdat

  • Adds 40 mm spacing for tight builds
  • Male-to-female G 1/4 in thread fits standard fittings
  • 45 mm overall height clears bulky components
  • Coated brass resists corrosion in coolant loops
  • Includes installed O-ring for leak-free seal

Tekniset tiedot

TypeCPU Block

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

What G 1/4in threaded components do I already need to connect this 40mm SX extension coupler?

You need at least one male G 1/4in fitting and one female G 1/4in port, such as on a water block, radiator, pump or reservoir, to thread the coupler between them.

Will the 45mm overall height with threads fit alongside my existing G 1/4in fittings in a tight loop?

The coupler adds 40mm of body length plus thread engagement, so measure the gap between your current fittings; if the clearance exceeds roughly 45mm it will fit without forcing adjacent tubing.

How can I confirm the coated brass coupler is sealed and oriented correctly after installation?

The male side ships with an installed O-ring; hand-tighten until the O-ring compresses, then pressure-test the loop — no leaks and proper alignment mean it is working as intended.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.