Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Small green circuit board with mSATA slot and SATA connectors

SMUGDESK

SMUGDESK 5cm LowProfile mSATA to SATA Adapter 2.5

SKU CH-4P1P-3HRF6

Converts an mSATA SSD into a 2.5 SATA drive for laptop storage upgrades

  • Converts mSATA SSD to 2.5 SATA for easy notebook storage upgrade
  • Compact 5cm low-profile PCB fits tight laptop chassis without space conflicts
  • SATA 6Gbps bandwidth preserves original SSD read-write performance
  • Plug-and-play installation requires no drivers or software
  • Reuses spare mSATA drive to replace mechanical HDD and boost responsiveness

Compact mSATA Adapter for Notebook Upgrades

This 5 cm low-profile board converts a standard mSATA SSD into a 2.5 inch SATA device. It is built for laptop and notebook owners who want to repurpose an existing mSATA drive as an internal storage upgrade. The bare PCB design fits tight chassis spaces without a metal enclosure. Installation is plug-and-play with no driver required.

SATA 3 Bandwidth and Backward Compatibility Limits

The adapter passes SATA 3 6 Gbps signals while remaining backward compatible with SATA 2 and SATA 1 host controllers. Throughput is therefore capped by the host port generation rather than the adapter itself. It cannot overcome the speed ceiling of an older SATA revision or the inherent limits of the mSATA SSD installed on it.

Replaces Mechanical 2.5 Inch Drives Using Spare

This board lets you swap a slow 2.5 inch hard drive for an mSATA solid-state drive you already own, improving boot and load times. It is not compatible with M.2 NGFF SSDs, so buyers with only M.2 drives cannot use it. The upgrade is worthwhile when a compatible mSATA SSD is available and the notebook has a free 2.5 inch SATA bay.

Põhijooned

  • Converts mSATA SSD to 2.5 SATA for easy notebook storage upgrade
  • Compact 5cm low-profile PCB fits tight laptop chassis without space conflicts
  • SATA 6Gbps bandwidth preserves original SSD read-write performance
  • Plug-and-play installation requires no drivers or software
  • Reuses spare mSATA drive to replace mechanical HDD and boost responsiveness

Tehnilised andmed

Selle toote kohta ei ole veel tehnilisi andmeid avaldatud.

Küsimused selle toote kohta

Should I choose a different adapter length or form factor for my laptop?

The board is a 5 cm low-profile PCB with no metal 2.5 inch shell, so it fits tight notebook bays where a full-height caddy would not.

Will my mSATA SSD keep its full speed once installed on this adapter?

The adapter passes SATA 3 6 Gbps bandwidth and is backward compatible with SATA 2 and SATA 1, preserving the drive's native read and write performance.

Does the SATA 3 interface limit the drive in any practical way?

The SATA 3 link caps transfer at 6 Gbps, so the SSD cannot exceed that ceiling, but the adapter adds no extra overhead beyond the standard SATA specification.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.